Resource library
Every source this manual draws on, grouped by chapter: agency handbooks, standards, makers' instructions and practitioners' methods, each fetched and checked on the date stated.
Every link was checked on 2026-11-10; next check due 2027-11-10. Each source is listed once, under the chapter that leans on it most. Nothing here carries a referral or tracking parameter. A few hosts (Fine Woodworking, Paul Sellers' blog, Common Woodworking, Lee Valley, Wood and Shop, Lost Art Press, CPSC) refuse automated requests; if a link does not open first time, try it again in a browser tab.
Where a newer document replaced an older one, only the newer is listed: Rust-Oleum's January 2026 Watco Danish Oil data sheet replaces a 2013 Canadian sheet, its January 2024 SealCoat sheet replaces a 2017 copy, and Sunnyside's 2015 boiled linseed oil SDS replaces its 2006 sheet. The Wood Handbook chapters are linked on the Forest Service's Treesearch site, because the Forest Products Laboratory's own site returned server errors throughout November 10, 2026.
A shop on a table
- How to do woodworking without a workbench, Common Woodworking (Paul Sellers). Starting with a few tools and sturdy clamps on an ordinary table.
- Make a pair of bench hooks, Popular Woodworking (Zachary Dillinger, 2022). The paired method on the quick start.
- Beyond the vise: planing boards, Popular Woodworking (Steve Branam, 2014). A planing board that hooks a table edge.
- The mystery of holdfasts, Popular Woodworking (Robert W. Lang). For a bench or board with holes, later.
- Safe use and disposal of household chemicals, New Mexico State University Extension (2019). Storage away from food and children.
- How loud is it?, Workers' Safety and Compensation Commission (Northwest Territories and Nunavut). The hammering figure.
- Noise exposure chart, University of Virginia Facilities Management (2023). Measured power tool levels, for comparison.
- Wood dust, U.S. Occupational Safety and Health Administration. The workplace hazards, and what is not established.
- Report on Carcinogens, National Toxicology Program; the 15th edition (2021) is the current one. Its wood dust profile lists wood dust as known to be a human carcinogen.
- Wood dust, International Agency for Research on Cancer, Volume 62 summary (1995), and Volume 100C (2012), which reaffirmed it.
- Wood dust: controlling the risks, UK Health and Safety Executive (revised 2022). Workplace guidance; avoid dry sweeping and compressed air.
- Hand and power tools, OSHA 3080 (2002). Hazards of damaged handles and misused chisels; written for employers.
- Household safety: preventing cuts, Nemours KidsHealth. Tools out of reach or locked away.
- First aid, linked and not paraphrased: Wounds, American Red Cross; Cuts and puncture wounds, MedlinePlus (reviewed 2025); Cuts and grazes, NHS (UK numbers).
The first tools
- Which hand tools do I need to get started?, The English Woodworker (Richard Maguire). A beginner kit and what can wait.
- You don't need much, Paul Sellers (2023). A lifetime kit, new and secondhand.
- Buying bench planes on eBay, Paul Sellers (2011). What to check on a used plane.
- A buyer's guide to antique handsaws, Fine Woodworking (2019). Sighting the plate for bends and kinks.
- Your basic guide to chisels, Popular Woodworking. Bevel-edge, firmer, paring and mortise chisels.
Sharpening
- Sharpening instructions, Lie-Nielsen Toolworks (rev. January 2024). Angles, the Ruler Trick, regrinding.
- How to sharpen, Lee Valley Tools. Flattening backs and the micro-bevel.
- Using the MK II honing guide, Lee Valley (Veritas). One guide's instructions.
- How to use a honing guide, Fine Woodworking (Asa Christiana, 2012). Angles for paring and struck chisels.
- Sharpening, Paul Sellers' knowledge base. Diamond plates and abrasive paper.
- Use and care instruction, DMT (on a retailer's site). Diamond plates dry or with water.
- Kuromaku waterstone FAQ, Shapton (on a retailer's site). Soaking rules for waterstones.
Choosing wood
- Wood Handbook (FPL-GTR-282, 2021), USDA Forest Products Laboratory: Chapter 3, structure (flatsawn and quartersawn); Chapter 4, moisture (shrinkage and equilibrium moisture tables); Chapter 6, lumber (grades, rough and S2S sizes); Chapter 13, drying and dimensional change (the movement formula and coefficients).
- Electric moisture meters for wood, Forest Products Laboratory (1988). What meters read and their limits.
- Wood and moisture relationships, Oregon State University Extension (EM 8600). Free and bound water.
- The shrinking and swelling of wood and its effect on furniture, Purdue Extension (FNR-163). Designing for movement.
- Controlling moisture content in stored lumber, Purdue Extension (FNR-403-W). How fast boards change.
- Understanding equilibrium moisture content, Penn State Extension. A table top that jammed its drawer.
- How to acclimate wood, Woodcraft (2026). Indoor targets by region.
- Why wood warps, Popular Woodworking (Glen Huey). Acclimating and rough-cutting oversize.
- American Softwood Lumber Standard PS 20-25, NIST (2025), and its status page, American Lumber Standard Committee. Nominal and actual sizes.
- Board foot, Virginia Department of Forestry. The definition.
- The grades, American Hardwood Export Council, and Hardwood log and tree quality, Ohio State University Extension. Hardwood grades.
- The Wood Database (Eric Meier): eastern white pine, yellow-poplar, red oak, Janka hardness, dimensional shrinkage and wood allergies and toxicity. The pages carry shop links; we link only the pages.
- Using grain pattern to choose lumber, Popular Woodworking (Robert W. Lang). Reading the end grain.
- Lumberyard prep, Popular Woodworking (Shannon Rogers). Planning before buying.
Measuring without numbers
- Story stick, Woodcraft. Marking sizes on a stick in place of a tape.
- Essential dividers and Honing in on proportions, Popular Woodworking (George Walker). Proportion with dividers.
- For dividers I fall and The golden meaningless, Popular Woodworking (Christopher Schwarz). Why arithmetic invites error, and whole-number ratios.
- By Hand & Eye and From Truths to Tools, Lost Art Press (George Walker and Jim Tolpin). Publisher's descriptions of two paid books; we read the descriptions, not the books.
- Handbook 44, Appendix B (2026) and SI units: length, NIST. The inch is exactly 25.4 mm.
- Precision rules, Starrett catalog. Reading a rule between two lines.
Marking out
- Measure, mark and lay out, Popular Woodworking (Robert W. Lang). The flip test and marking one part from another.
- All about try squares, Popular Woodworking. The flip test, and knifing round a corner.
- An intro to marking knives, Popular Woodworking (Yoav Liberman, 2015). The knife wall.
- Knifewalls, Paul Sellers (2023). His term and method.
- Make your mark and Customary marks, Popular Woodworking. Face and edge marks.
- Mystery of the marking gauge, Popular Woodworking (Dean Jansa, 2006). Setting and running a gauge.
Sawing to a line
- Japanese saw guide for beginners, Woodcraft. The ryoba as a starter saw.
- Rip and crosscut tenon saws, Lee Valley (Veritas). Tooth counts, rake and set on one maker's saws.
- Margins in cuts for hand work, Paul Sellers (2014). Sawing to the line.
Planing a board square
- Bench planes instructions, Lie-Nielsen Toolworks (on a retailer's site, rev. 2019). Blade, chipbreaker and mouth settings.
- Setting the blade, Lee Valley (Veritas). Depth and lateral adjustment.
- Handplaning 101, Fine Woodworking (Chris Gochnour, 2009). Setting up a bench plane.
- Use winding sticks to ensure flat stock, Fine Woodworking (2005). Seeing twist.
- Reading grain direction, Popular Woodworking (2014). Planing with the grain.
- What's a shooting board, Popular Woodworking (Christopher Schwarz, 2023), and Build a shooting board, Fine Woodworking (David Finck, 2008).
Housings and rabbets
- All about rabbet and dado joints, Fine Woodworking (Mario Rodriguez, 2005). The one-third depth convention.
Mortise and tenon
- Tenons rule, Popular Woodworking. Thickness, length and width conventions.
- Joining legs to aprons, Fine Woodworking (Garrett Hack, 2003). A slightly thicker tenon in soft wood.
- Drawbore with Andy Rawls, Popular Woodworking. The offset limit.
- The wedged mortise and tenon, Popular Woodworking (Peter Follansbee, 2023). The tusk tenon, wedged through its end.
- Wedged mortise and tenon, Popular Woodworking (Tom Caspar). Flaring the mortise and placing the kerfs; the tooling is power tools, the principle is not.
- Avoiding splits with wedged tenons, Woodcraft (Ken Burton). Kerfs across the grain of the mortised piece.
- Diagonal wedges: the how and why, Popular Woodworking (Christopher Schwarz, 2017). Why wedges push on end grain.
- Wedged and pegged tenons, Paul Sellers (2015). Paring the mortise ends by hand.
Dovetails
- Hand-cutting dovetails, Popular Woodworking (Logan Wittmer, 2024). Tails first, step by step.
- Demystifying hand-cut dovetails, Woodcraft (Rob Cosman). Spacing with dividers.
- Hand cut through dovetails, Woodcraft (Frank Klausz's method). Pins first, angles by eye.
- My take on dovetail angles, Popular Woodworking (Glen D. Huey), and Proper angles for dovetails, Woodcraft (Chris Hedges). The slope convention and its critics.
- Tails and pins: which is best? and Understanding softwood dovetails, Paul Sellers. Tails first, and pencil layout in pine.
Glue, finish and mending
Glue
- Titebond specifications, Franklin International: Original, II, III, Genuine Hide Glue, and the FAQ on clamp times. Open times and temperatures.
- FAQ, Old Brown Glue. Liquid hide glue, warming and reversing.
- Wood adhesives, Wood Handbook Chapter 10, Forest Products Laboratory. Open time, clamp pressure and starved joints.
Finish
- Rust-Oleum and Zinsser data sheets: Bulls Eye Shellac (2022), SealCoat (January 2024) and its SDS (March 2026), Watco Danish Oil (January 2026), Watco Danish Oil 350 VOC (January 2026) and the Watco SDS (March 2024).
- Minwax product pages and labels: Paste Finishing Wax, Wipe-On Poly, Polycrylic, Tung Oil Finish, Wood Finish stain (its rag warning) and Food-Grade Wood Oil (a maker's own food-contact claim).
- Dry time and cure time, General Finishes. One maker's cure figures.
- Boiled linseed oil SDS, Sunnyside (2015). The rag warning.
- FAQ, Tried & True. A polymerized linseed oil maker's rag method.
- Wood Bowl Finish data sheet, General Finishes (2020, on a retailer's site). Dry and cure times for an oil-based finish.
- Rags and fire: Safe disposal of oily rags, City of Piedmont Fire Department (2026); Flammable and combustible liquid safety, Washington State Fire Marshal (2026); Spontaneous combustion, fact or fiction?, National Park Service.
- Solvents: odorless mineral spirits SDS and denatured alcohol SDS, Klean-Strip. Ventilation and flammability.
- Food contact: 21 CFR 175.300, FDA; Finishes for wood bowls and toys, Forest Products Laboratory (2013); Behlen Salad Bowl Finish data sheet, Mohawk (a maker's claim); Is polyurethane food-safe?, Popular Woodworking (a practitioner's view).
Mending, lead and strippers
- The best way to reglue furniture, Popular Woodworking (Bob Flexner, 2007), and his Regluing doweled chairs. Repair methods ranked.
- Adhesives for the conservation of fine furniture, Building Conservation Directory. Hide glue and PVA compared.
- A gentler approach to fixing your wobbly legs, West Dean College (2020). A conservation case where dismantling did harm.
- Conserve O Gram 7/7, National Park Service. Protein glues and water.
- Lead: Reduce the risk from lead exposure in your home and Lead test kits, EPA (2026); Home lead test kits unreliable, CPSC (2007); 16 CFR Part 1303, the lead paint ban for furniture made after February 27, 1978.
- Methylene chloride: Risk management for methylene chloride, EPA (its 2019 consumer paint-remover section is current; its 2024-rule text is not); East Fork Enterprises v. EPA, Fifth Circuit opinion (September 15, 2026) and its docket (mandate issued October 2, 2026); law firm summaries from Crowell & Moring and K&L Gates. Status as of 2026-11-10.
Classes and video series elsewhere
Listed as references only: these are the curricula we compared when planning this manual. Nothing here is a recommendation, and we receive nothing from any of them. Prices are as shown on 2026-11-10 and change.
- Common Woodworking (Paul Sellers). Free step-by-step projects, from a chisel tray to a tool tote.
- How to get into woodworking with hand tools, Wood and Shop. A free ten-step guide, including small-space shops.
- Orientation ($75) and Semester 1 ($100), The Hand Tool School (Shannon Rogers). Online, project-based.
- The Spoon Rack, The English Woodworker (GBP 26). One small object, start to finish, on video.
- The Foundations Course, Mortise & Tenon Magazine ($25). Joint demonstrations.
- Woodworking Masterclasses (Paul Sellers). A project video library with a free tier.
- Rob's Online Workshop (Rob Cosman). Subscription project episodes.
- In person: Introduction to Hand Tool Woodworking, Wood and Shop, Virginia (3 days, $595); Fundamentals of Hand Tool Woodworking, North Bennet Street School, Boston (10 days, $1,650); Hand Tool Woodworking: Getting Started, North House Folk School, Minnesota (3 days); Foundations of Woodworking I, Port Townsend School of Woodworking, Washington (12 weeks).
These are the sources behind this manual, not an endorsement of any of them and not a complete literature. Makers appear as the source of their own published figures. Agency workplace guidance is written for employers, and the chapters say so when they quote it. If a figure matters to a decision you are making, read the source rather than our summary of it.