Cut list, boards, movement and dovetail calculators
Reference

Cut list, boards, movement and dovetail calculators

Four calculators: the tote's parts from its inside sizes, the boards to buy and whether the parts fit them, how much a board will move with the seasons, and a dovetail's slope and spacing. Each lists what its figures rest on.

Lengths in inches take 11 1/2, 11-1/2, 11.5 or 3/4; in millimeters, a plain number. The boxes open with the sizes of Noor's tote (fictional; see Measuring without numbers), so every result can be checked against a worked case before you enter your own.

Tote cut list from what it carries

Enter the inside sizes from your story stick. Inside length runs between the ends and inside width between the sides, each including the divider's thickness if the divider runs that way. Heights are outside heights, from the underside of the bottom. The result lists every part with its finished and rough size and flags any part wider than the boards you have. It is arithmetic on the conventions listed under Assumptions; your stick is the check.

Boards to buy

Choose the size on the label. Softwood boards are named by a nominal size; hardwood is named by quarters of an inch of rough thickness and sold in random widths, so enter the width of the board in front of you. Add the cut list's total rough length and widest rough part to see whether they fit.

How much will this board move

Wood swells and shrinks across its width as the air around it gets damper or drier, and hardly at all along its length. This box applies the Wood Handbook's dimensional change method to one board: the coefficient for its species and grain, the moisture content it has now, and the driest and dampest it will reach. The Handbook says the method holds only between 6 and 14 percent moisture content, so outside that range the box shows no figure. Temperatures are in Fahrenheit with inches, Celsius with millimeters.

Dovetail spacing and slope

Enter the width of the joint (the height of the wall being joined), how many tails, the slope, and the widths of the half pins and pins at their narrow face. The box gives the tail width, the spread to set on your dividers and the marks from one edge. Dovetails lays out the same joint with dividers alone; this box is for checking or for readers who want numbers.

Fictional example

The boxes open with fictional figures. The cut list and the board are Noor's: inside 9 1/4 by 6 3/4 in, rabbeted corners, ends with the grain up and down, a lengthwise divider, and 1x6 boards. The cut list flags her ends (7 1/2 in wide rough) and her bottom as wider than a 1x6, which is how she found she needed a 1x8 for the ends and two pieces side by side for the bottom. The movement box is one of her 7 1/4 in ends, species unknown, indoors. The dovetail box is Hal's 7 1/4 in yellow-poplar side at 1:7 with four tails.

Limits

These boxes do arithmetic on the figures you enter and on published conventions and averages. They do not say a joint is strong enough, that a board will stay flat or that a part will not crack, and they cannot see knots, splits or a board that has not settled. Check every size against your story stick and the wood in front of you before cutting. Movement figures are estimates from averages that vary from piece to piece.

Assumptions behind the numbers

  • Cut list. Stock 3/4 in thick by default, the dry size of a nominal 1 in board (NIST PS 20-25). Housing depth one-third of the thickness by default, and never more than half, and rabbet depth about one-third, at least 1/4 in in 3/4 in stock (Fine Woodworking, rabbets and dadoes). Tenon thickness one-third of the stock it passes through, tenon height half the handle's height (Popular Woodworking, rules on tenons). Rough sizes 1 in over length and 1/4 in over width (Popular Woodworking, why wood warps). About 1/32 in lost to each cut, from the plate and set of Lee Valley's tenon saws (a ryoba's kerf differs). The sides are rabbeted and the ends sit in them; with dovetails, sides and ends both run the full outside size. The bottom is nailed under the box. Clearance is your own figure; no source gives one.
  • Boards. Dry sizes of nominal softwood boards and the board measure rule (nominal thickness by nominal width in feet by length in feet) from NIST PS 20-25. Hardwood rough and surfaced-two-sides thicknesses (4/4 is 1 in rough, 13/16 in S2S) from the Wood Handbook, chapter 6. A board foot is 144 cubic inches (Virginia Department of Forestry). The fit check is by length only.
  • Movement. Equilibrium moisture content from Table 4-2 of the Wood Handbook, chapter 4, interpolated between its rows (30 to 100 F) and columns. Dimensional change coefficients from Table 13-5 and Equation 13-3 of the Wood Handbook, chapter 13: change = width times coefficient times (final minus starting moisture content), valid from 6 to 14 percent, underestimating by about 5 percent. Ranges from Table 13-2 (individual pieces): interior and exterior, for most of the US, the dry Southwest and the damp warm coast; we use the exterior row for an unheated garage or shed, which the Handbook does not name. "Not sure" uses the largest coefficients in the list (white oak tangential, basswood radial).
  • Dovetails. A slope of 1 to n is an angle of arctangent 1/n: 1:6 is about 9.5 degrees and 1:8 about 7.1 (Popular Woodworking, dovetail angles). The width is two half pins, the tails at the board's end and the pins between them; each side of a tail narrows toward the baseline by the pin board's thickness divided by n. The dividers' spread is one tail plus one pin (Rob Cosman, Woodcraft). The slopes for softwood and hardwood are a convention, not a strength rule.