A shop on a table: working wood without a workshop
A heavy table, a protective board and three shop-made aids hold the work for sawing, planing and chopping, with noise, dust, neighbors and children planned for.
Start here Essentials
At minimum this chapter asks you to pick a table and a time of day, cover the top, and set up two holding aids that keep a board still while you saw and plane it. Everything marked Go deeper is optional on a first pass.
- Choose the table and the hours you will work. A heavy table that does not rock, and quiet hours your building accepts (The surface, Noise and neighbors).
- Put a protective board on the top. Every saw cut, knife line and chisel blow lands on it, not on the table (The surface).
- Make or buy a bench hook. It holds a board for sawing with no clamp (Make a bench hook this weekend, Sawing and chopping without a vise).
- Clamp the planing board to the table edge. Its stops take the push of the plane (The planing board).
- Choose where the sharp tools live. Out of reach or locked, if children live or visit (Dust, finishes and sharp tools).
Minimum time: about an hour, once the bench hook exists. Done when: a scrap board can be sawn on the bench hook and planed against the stop without either one sliding.
1. The surface Understand
Hand-tool work asks two things of the place you do it. The surface should stay still, and there should be a way to stop the work moving on the surface. A workbench does both at once: it is heavy, and its vise and holes grip the board. A kitchen or dining table can do the first if you choose it well. Three shop-made aids do the second, and none of them needs a vise. A vise is a clamp built into a bench that grips a board between two jaws.
The first quality is weight. A saw stroke, a plane stroke and a mallet blow all push the table. A heavy table absorbs the push; a light one slides, rocks or bounces, and the work moves with it. Push down on one corner of the table and then sideways on its edge. If it rocks on an uneven floor, a folded card under the short leg fixes the rock but not a loose joint. If the legs wobble in their joints, the table is a poor surface for chopping, whatever its weight. Test it
The second quality is a solid edge. The bench hook and the planing board both hook over the edge of the top, so the edge has to be square enough to catch them and strong enough to take the push. A rounded edge, a thin glass top or an overhanging leaf on hinges gives them nothing to catch.
The third quality is height. We found no fetched source that gives a working height for planing on a table, so we give none. What you will notice is this: planing at a dining table is a little high for most people, and sawing at it is about right. If planing tires your arms quickly, stand on a sturdy platform or plane on a lower surface.
Protecting the top
Put a sacrificial board under every operation. That is a flat sheet you expect to cut into: a piece of plywood, or hardboard (a thin, dense sheet made of pressed wood fibers, sold at home centers). The saw finishes its cut into it, the knife runs onto it, and a chisel that goes through the work stops in it. Replace it when it is scarred. A blanket or towel under the sacrificial board keeps grit off a veneered top, but a soft layer also lets the board shift, so test both ways and keep the one that stays put. Test it
A veneered top has a thin layer of good wood glued over a core. A knife line or a chisel nick goes through veneer quickly, and planing it out, as you could on solid wood, would go through the veneer too. Treat a veneered table as a surface you are borrowing, not one you will repair. If the table belongs to a landlord, what you may change about it is in your lease: Learn First Home Basics on repairs and requests covers how to ask.
Light
A knife line or a gauge line is a groove, not a mark. It shows best when light falls across it from low to one side, so the groove's wall throws a thin shadow. A small lamp set low on the table, to the side opposite your working hand, does this. Overhead light from straight above flattens the line. This is our practice; we found no source that measures it. Preference
Where the table goes
Work needs room on both sides of the board: a saw stroke runs out past the work, and a plane stroke needs the length of the board plus the plane. Keep a clear path behind you, and keep the work area out of a walking route. Learn Space Planning on small homes and its chapter on safety in the layout cover clearances around furniture.
2. Sawing and chopping without a vise
Each operation pushes the work in a different direction, so each needs its own way of holding. The table below is the whole system. The rest of this section and the next explain each row.
| Operation | What holds the work | Where the force goes | What goes under it |
|---|---|---|---|
| Crosscutting a short part to length | Bench hook: your free hand presses the board against its fence | Into the fence, then the hook, then the table edge | The bench hook's own base |
| Ripping a part to width | Clamps, with the cut line past the table edge | Into the clamps and the table | Nothing: the saw runs past the edge |
| Planing a face or an edge | Planing board: thin stops on top, a strip underneath hooked on the table edge | Into the stop, then the hooked strip, then the table edge | The planing board |
| Trimming an end square | Shooting board (a bench hook with a track for a plane) | Into its fence and hook | The shooting board |
| Chopping with chisel and mallet | Clamps, with the work directly over a leg | Down the leg into the floor | The sacrificial board |
The bench hook
A bench hook is a flat board with a strip, called a fence, across the top at the far end and a second strip, the hook, across the underside at the near end. The hook catches the table edge. You press the work against the fence with your free hand, and the saw cuts beside the fence into the base. Nothing is clamped: gravity and the two fences hold it. Zachary Dillinger's pair of bench hooks in Popular Woodworking are made as one board and then sawn apart, so both fences match and the two hooks can support a longer piece together. His have an 18 in working length cut from a 24 in board, with fences about 3/4 in thick.
The bench hook carries every crosscut in this manual, which means every cut across the grain to bring a part to length. It also catches knife slips and saw run-outs that would otherwise land on the table. Make a bench hook this weekend builds one from a single pine board, and its last step makes the first square cut on the finished hook.
Whichever saw you use, the free hand does the holding. With a push saw, the stroke drives the work into the fence. With a pull saw, such as the ryoba recommended in The first tools, the stroke draws the work toward you, so press the board firmly into the fence and keep the strokes light. Some people turn the bench hook around for a pull saw. Try both on scrap and keep the one where the board stays still. Test it
Ripping on a table
A rip cut runs along the grain, to bring a part to width. The tote's parts are short, but a rip still runs their full length, so it does not fit on a bench hook. Clamp the board flat on the table with the cut line just past the edge, so the saw runs down beside the table rather than into it. Saw until the clamp is in the way, then move the board and clamp it again. Paul Sellers' article How to do woodworking without a workbench starts from exactly this kit: a small collection of tools and some sturdy clamps on an ordinary table top.
A clamp here means an F-clamp or a bar clamp: a steel bar with a fixed jaw and a sliding jaw that screws tight. Put a scrap of wood under each jaw, so the jaw does not dent the work or the table.
Chopping over a leg
Chopping means driving a chisel with a mallet, to cut a mortise or the waste between dovetails. It is the hardest blow you will put into a table. A tabletop is a beam held up at its legs. Struck halfway between two legs, it flexes and bounces, the chisel jumps, and some of each blow is lost in the bounce. Struck directly over a leg, the blow goes down the leg into the floor. Physical principle So clamp the work to the top directly over a leg, on the sacrificial board, and chop there.
If no part of the top sits over a solid leg, chop on the floor: a thick scrap block on a hard floor, the work clamped to the block or held under your knee. A folding table, a table that rocks, or a glass top is not a surface for chopping.
We cannot see your table, and nothing in this chapter says a particular table is strong enough for chopping. The tests above tell you what to watch for: rocking, wobbling joints, a top that bounces under a blow. If any of them shows up, chop on the floor. A table someone else owns is theirs to decide about, and a landlord's furniture is covered by the lease.
The shooting board
A shooting board trues the end of a board. It holds the work at 90 degrees to a track that a plane runs along on its side, so the plane shaves the end square. Christopher Schwarz, in his shooting board primer for Popular Woodworking, describes it as the way to square an end when there is 1/32 in or less to remove, and notes that a bench hook can serve as one. David Finck's weekend shooting board in Fine Woodworking names the two things that have to be right: the stop square, and the stop flush with the edge that guides the plane. It is made in Planing a board square, once you have a plane and know how to set it.
If a bench comes later
A table, a bench hook, a planing board and clamps will build the tote. A workbench is a later choice, and the most common first project in the paid curricula we read. The Hand Tool School's Orientation starts by building a workbench from construction lumber, in a garage, with bench hooks recommended even before it exists. That suits a reader with a garage and a weekend for heavy work. Hal (fictional), who has an unheated garage, could go that way; Noor (fictional), on a third floor, would not.
Holdfasts are the other thing a bench brings. A holdfast is a bent iron rod that drops into a hole in a bench top; a few light taps wedge it, and it pins the work down. A rap on its back releases it. Robert W. Lang's tests, in The Mystery of Holdfasts, found that the hole's diameter, the shaft size and the thickness of the top all change how well one grips. A holdfast needs a hole through a thick top, so it is not something to try in a dining table. Some woodworkers put holdfast holes in a thick separate board that clamps to a table; we found no fetched source that tests that, so we name it only.
A pair of folding sawhorses with a thick plank across them is a third surface: low, cheap and easy to store. It suits ripping long boards, which the tote does not need. We found no source that compares sawhorses with tables for hand work, so this is a suggestion only.
3. The planing board
A plane is pushed along the board, and the push moves the board unless something stops it. On a bench, a planing stop (a block raised a little above the top) does that. On a table, a planing board does: a flat board with thin stops fastened along its top edges and a thicker strip fastened underneath at the front, which hooks over the table edge like a bench hook. You push the plane toward the stops, and the stops take the push.
Steve Branam's design, in Beyond the Vise: Planing Boards, was made for exactly this: planing faces on a table that was not set up for it. His board is 18 in square and takes parts up to 16 in long. Two thin stop strips run along the back edge and the left edge on top, and a thicker strip runs along the front underneath. The tote's longest parts are 10 3/4 in for Noor (fictional) and 18 in for Hal (fictional), so Branam's size suits Noor and a board a little longer suits Hal; size yours to your longest part.
How to use it
- Hook it and clamp it. Hook the underside strip over the table edge. A clamp at each back corner stops the far edge lifting. Branam's board relies on the hook; the clamp is our addition for a light table. Preference
- Set the work against the stops. The work's end goes against the back stop and its edge against the side stop.
- Plane toward the stops. Every stroke pushes the work further into the corner it is already in.
- Check that the stop sits below the surface you are planing. The stop has to be thinner than the work, or the plane's blade hits it at the end of every stroke. Use thin stops for thin parts.
The planing board also gives you a place to plane an edge. Clamp the part on edge against the side stop with a clamp at the far end, or hold it in a simple wedge; the technique of planing an edge straight and square is in Planing a board square, which links back here.
Whatever you hold the work with, the plane needs room to run off the far end of the board. A stop that sits proud of the work's end stops the plane as well. If the plane hits the stop, the stop is too thick or too high; plane a thinner one rather than shortening the stroke. Test it
Planing makes shavings, not dust. They pile up on the floor and the board, and they slip underfoot on a hard floor. Sweep them up before you walk away, and before anyone else walks through.
Planing is the operation that moves a light table most. If the whole table creeps across the floor, put it against a wall at the far end, so the wall takes the push, or plane with lighter cuts. A rubber mat under each leg also helps on a smooth floor; that is our observation and we found nothing that measures it.
4. Noise and neighbors
Hand tools are quieter than power tools, but not all of them are quiet. Sawing and planing are steady, low sounds. Chopping with a mallet is a series of sharp blows, and those blows travel through the table legs into the floor and into the room below.
Two published charts give the scale. The University of Virginia's noise exposure chart for commonly used tools measured power tools from 93 dBA (a drill) to 109 dBA (a circular saw). It has no figure for a hand saw or a chisel. The Northwest Territories and Nunavut workers' safety commission's chart, How Loud Is It?, gives hammering at 94 to 97 dBA, and notes that hearing loss can follow extended exposure at or above 85 dBA. A dBA is a decibel weighted the way the human ear hears; each 10 dBA step sounds roughly twice as loud. Hammering is the only hand-tool figure we found, and it sits among the power tools. We found no measurement of a hand saw or a plane, so we give none.
What this means in practice:
- Saw and plane whenever the household is awake. These are the quiet operations.
- Schedule chopping. Mortises and dovetail waste are chopped in short sessions at hours the neighbors would accept. Paring by hand pressure, without the mallet, is close to silent and does much of the same work in soft wood.
- Chop over a leg, on the floor if you can. A blow struck over a leg goes straight down; whether it is quieter below we cannot measure. A thick rubber mat or a folded rug under the table leg or the chopping block may soften the knock in the room below. That is our observation, not a measured figure.
- Ask. A neighbor who knows you will chop for twenty minutes on Saturday morning takes it better than one surprised at 9 p.m.
Quiet hours in a rented home are set by the lease and the building's rules, and sometimes by a local noise ordinance. Read the lease and ask the landlord if it is unclear. Ask the authority Learn First Home Basics on limited space covers living alongside neighbors in a small home.
5. Dust, finishes and sharp tools in a home
Dust
Saws make sawdust and planes make shavings; both are coarse and fall to the floor. Sanding, even by hand, makes fine dust that stays in the air. Agency guidance is written for workplaces and measures power sanding, not hand work. OSHA's wood dust page says dust becomes a health problem when particles from sanding and cutting become airborne, and that breathing it may cause allergic and respiratory symptoms and cancer. The UK Health and Safety Executive's information sheet Wood dust: controlling the risks says all wood dust can cause asthma, dermatitis and irritation of the eyes, nose and throat. It lists dry sweeping and compressed air among the tasks that raise exposure.
We found no measurement of hand sanding, so we give no figure for it. What follows from the agency guidance:
- Plane and scrape rather than sand where you can. A sharp plane leaves a finished surface and a pile of shavings.
- Clean up with a vacuum or a damp cloth. Do not blow dust off, and avoid dry sweeping fine dust; a broom is fine for shavings.
- Sand outdoors or by an open window, and wipe the table afterward, since it is also where you eat.
- Some woods cause reactions. The Wood Database's page on wood allergies and toxicity lists common species as irritants or sensitizers and notes that very few woods are toxic. If a wood makes your skin, eyes or breathing react, stop working it and ask a doctor. Ask the authority
Glue, finishes and the kitchen
A kitchen table is where food is prepared and eaten, so we keep finishing off it: glue-ups can happen on the table on a covered board, but oils, varnishes and solvents are applied somewhere else, with the ventilation their labels state. That is our rule, not an agency's. New Mexico State University's extension guide Safe use and disposal of household chemicals gives the storage rules: do not store household chemicals on shelves used for food, do not keep them in containers people recognize as food containers, keep products in their original containers and out of children's reach, and not to pour solvent-based products down a drain. Oily finishing rags can heat up and catch fire on their own; Glue, finish and mending covers how to deal with them, from the product labels.
Where the sharp tools live
A chisel, a marking knife and a saw are made to cut, and they cut skin as readily as wood. Nemours KidsHealth's page on preventing cuts at home advises keeping all tools out of reach or in locked storage. Where children live or visit, choose a place for the edge tools that meets that: a high shelf, a cupboard with a lock, or a toolbox with a padlock. Keep it the same place every time, so nothing is left on the table between sessions.
Two habits protect the tool and the hand together. Put chisels down with the edge away from you and not hanging over the table edge, and cover each edge when it is stored: a cap, a roll with a pocket per tool, or a slotted block. A covered edge also stays sharp longer, which matters in Sharpening.
If you cut yourself, follow a first aid page, not this manual. The American Red Cross page on wounds and MedlinePlus on cuts and puncture wounds say when a cut needs care. For a cut that will not stop bleeding, call 911 or your local emergency number.
Keep both hands behind the edge. Clamp the work instead of holding it in front of a chisel, and cut away from your body. The holding aids in this chapter exist so that your free hand has somewhere safe to be.
6. See it See it
Noor (fictional) sets up on her dining table. Noor rents a third-floor apartment with neighbors below and works on a 30 by 48 in dining table with a veneered top. She owns no tools yet. She pushes on each corner: the table does not rock, and its legs are tight. She buys a 2 by 4 ft sheet of hardboard for the top and lays it over a towel; the hardboard slides on the towel, so she drops the towel and puts thin felt pads under the hardboard's corners instead. Her first tool purchase is the bench hook's material, and she makes it on the table with a borrowed saw, as the quick start describes. For planing, she makes a planing board at Branam's 18 in square; her longest tote parts, the sides, handle and bottom pieces, are 10 3/4 in long, so they fit with room to spare. She clamps its back corners to the table. She chooses the table's left end, which sits over a leg, as the chopping spot.
Known: the table's size and that it does not rock; the length of her longest part (10 3/4 in); that she lives above a neighbor. Assumed: that the veneer is too thin to plane a mark out of, which is her own cautious assumption and why every operation sits on the hardboard. Open: whether the downstairs neighbor minds mallet work after 8 p.m. Noor settles it by asking; the neighbor prefers Saturday mornings, so she chops then. Also open: what her lease says about quiet hours, which the lease and her landlord settle, not this manual.
- Make a pair of bench hooks, Popular Woodworking: one board made into two matched hooks, with photographs of the hook holding work for a cut.
- Beyond the Vise: Planing Boards, Popular Woodworking: the planing board this chapter uses, drawn and shown on a table.
- What's a shooting board, and why do you need one?, Popular Woodworking: how the board and plane work together, with a bench hook doubling as one.
7. Practice Practice
Minimum: the table covered, the bench hook hooked on the edge, one scrap sawn across on it; the planing board clamped, one scrap pushed hard against its stop without sliding. If you have no plane yet, push the scrap with the heel of your hand along the line a plane would take. Time: about an hour, plus the time to make the planing board. Materials: the bench hook from the quick start; a flat board for the planing board, a little longer than your longest part; two thin strips for the top stops and one thicker strip for the underside; glue or screws; two clamps; a sheet of hardboard or plywood for the top; a scrap of pine.
- Test the table. Push down on each corner and sideways on each edge. Note any rock or wobble, and which corner sits over the most solid leg.
- Cover the top. Lay the sacrificial board and check that it does not slide when you push the bench hook against it.
- Saw on the bench hook. Hook it on the edge, hold a scrap against the fence and make one crosscut. Watch the hook: if it lifts or slides, press down harder with the holding hand.
- Make the planing board. Fasten the two thin stops along the back and left edges of the top face and the thick strip along the front of the underside, as Branam describes. A left-handed worker may put the side stop on the right; plane toward whichever stop takes your push.
- Clamp and push. Hook it, clamp the back corners, set a scrap against the stops and push hard toward them. Nothing should move.
- Find the chopping spot. Mark the place on the sacrificial board that sits over the solid leg you found, and write it down with your quiet hours in the tools and wood sheet's notes column, beside the holding aids.
8. Your setup Your setup
9. Check your work Check your work
Criteria
- Does the table stay still when you push on its corners and edges?
- Does every operation happen on the sacrificial board, not on the table itself?
- Does a scrap stay against the bench hook's fence through a full cut?
- Does a scrap stay against the planing board's stops under a hard push, with the board itself not lifting?
- Do you know where you will chop, and at what hours?
- Do the edge tools have one place, out of a child's reach or locked?
Worked example
Imani (fictional) works at a shared workbench in the basement of the two-flat she rents, so her setup starts from a bench rather than a table. The bench has a vise, but other tenants use it, so she makes the bench hook and planing board anyway and leaves the vise set for whoever is next. She checks the criteria. The bench is heavy and does not move. She uses a sheet of hardboard so her knife lines do not mark a shared top. Chopping is the open question in a two-flat: the upstairs tenants hear it through the floor joists, so she asks them, as Noor did. The tool question is sharper for her than for Noor: her daughter June, 9, lives with her and goes down to the basement for laundry. Her chisels live in a locked toolbox, and she takes them out only while she works. Each criterion has an answer, so her setup is done.
Common mistakes
- Holding the work in the air. A board held in one hand while the other saws or chisels is the setup the holding aids replace. If the work is not against a fence, a stop or a clamp, stop and set it up.
- Sawing into the table. Every crosscut finishes in the bench hook's base or the sacrificial board. A saw kerf in a table top is permanent.
- Chopping mid-span. The blow bounces and the chisel jumps. Move the work over a leg.
- A stop thicker than the work. The plane hits it every stroke. Make a thinner stop for thin parts.
- Tools left on the table. A chisel left out between sessions is within anyone's reach. Put it back every time.
- Blowing dust off the work. It puts the fine dust in the air you are breathing. Vacuum or wipe.
What is still unresolved
- Which saw, plane and chisels to put on this setup: The first tools.
- How to start and finish a cut square on the bench hook: Sawing to a line.
- How to plane against the stop, and the shooting board: Planing a board square.
- Whether your lease allows the work, and its quiet hours: your lease and your landlord.
- Whether a particular table is sound enough to chop on: you, by the tests above; when in doubt, the floor.