Glue, finish and mending
Joints and assembly

Glue, finish and mending: assembling the tote and fixing a loose joint

Dry-fit and glue up within the glue's open time, finish for where the piece will live, deal with oily rags by the label, and mend a loose chair or drawer joint.

Start here Essentials

At minimum this chapter asks for one rehearsed glue-up, a check for square, and two thin finishes. Mending a household joint is its own job, for when you have one. Everything marked Go deeper is optional on a first pass.

  1. Dry-fit the tote and rehearse the clamping. Time the rehearsal against the glue's total assembly time (The dry run and the glue).
  2. Glue up within the open time and check the diagonals. Equal diagonals mean a square box (Gluing up the tote).
  3. After the clamp time, flush the joints and apply dewaxed shellac. Thin coats, in a ventilated room (A finish for where it will live).
  4. Wax after the shellac dries, then nail on the bottom. Put the rags and cans away by their labels (Oily rags, solvents and storage).

Minimum time: about an hour for the dry run and glue-up, a day for the glue, and an evening for the finish. Done when: the tote is glued, square by its diagonals, finished, and carrying its contents.

1. The dry run and the glue Understand

A glue-up is the one step in the build with a clock running. Once glue is on the wood, you have a few minutes to close every joint before it starts to set, and a joint that sets half-closed stays that way. So the glue-up is rehearsed dry first: every part, every clamp, every move, in order, with a timer.

The two times on the bottle

Glue makers publish two figures, measured at 70 F and 50 percent relative humidity. Open assembly time is how long glue can sit spread on the wood before the joint is closed. Total assembly time is how long you have from spreading the first glue to having every clamp tight. The Wood Handbook defines the same ideas as open time, closed time and clamp time, and notes that higher temperatures shorten all of them (Wood Handbook, chapter 10, Wood Adhesives).

Glue (maker's sheet)Open assemblyTotal assemblyUse aboveComes apart later?
Titebond Original (yellow glue)4 to 6 minutes10 to 15 minutes50 FNot readily
Titebond III8 to 10 minutes20 to 25 minutes47 FNot readily
Titebond Genuine Hide Glue (liquid)10 minutes20 to 30 minutes50 FYes, with moisture and heat

Product-specific These figures are for these products; another brand prints its own, and the bottle in your hand is the one that counts. Titebond Original's sheet says the glue, the air and the wood should all be above 50 F. That matters to Hal (fictional), whose garage is about 45 F in March: below every minimum in the table. He glues up in the kitchen and leaves the tote there overnight.

Noor's (fictional) has four rabbeted corners, two slots for the divider and two tenons for the handle: eight joints to glue and close. Fifteen minutes is short for eight joints at a first attempt, so our default for the tote is the glue in the table with the longest total time you can buy: liquid hide glue or Titebond III. Preference Hide glue has a second reason: a joint made with it can be taken apart again, which is what mending is about.

The dry run

  1. Lay out every part in assembly order, each joint numbered as you fitted it, on a board covered with paper or plastic so glue does not reach your table.
  2. Set every clamp to its opening and put pads of scrap under the jaws so they do not dent the wood.
  3. Assemble the whole tote dry, start a timer, and clamp it.
  4. Check the diagonals (see Gluing up the tote).
  5. Stop the timer. If the rehearsal took longer than the glue's total assembly time, glue up in two stages.

The order is set by the handle. Its tenons pass through both ends, and on all three fictional totes the divider is housed in the ends too, so the ends, the handle and the divider go together first, and the sides close round them. That gives a natural two-stage glue-up: stage one is the ends on the handle and the divider; stage two, after its clamp time, is the sides. Imani (fictional), who wedges her through tenons, drives the wedges in stage one with glue on them, as Mortise and tenon describes.

2. Gluing up the tote

Spread glue on both surfaces of each joint where they meet: the cheeks of tenons and the walls of mortises, the faces of tails and pins, the bottom and wall of each rabbet. A thin, even film is the aim; Titebond's sheet gives about 6 mils, a coat you can see through to the grain.

Clamp only hard enough to close the joint. Titebond's wording is pressure enough to bring the joints tightly together. Physical principle The Wood Handbook explains why more is not better: pressure brings the surfaces into contact and thins the glue film, but too much squeezes out so much glue that the joint is left without enough, a starved joint. A well-fitted joint closes with modest pressure. If a joint needs a lot of force to close, the fit is the problem, and clamps will not fix it.

Check the box for square by its diagonals. Measure from one inside corner to the opposite corner, then the other pair. A rectangle's diagonals are equal, so equal readings mean the box is square. If one is longer, the box is racked, pushed into a parallelogram. Ease the clamps, press the two corners of the long diagonal toward each other, retighten and measure again. Do it while the glue is wet; after it sets, a racked box stays racked. A story stick laid corner to corner and marked does this without numbers, as Measuring without numbers describes.

Deal with squeeze-out. Titebond says to wipe wet glue with a damp cloth, or to scrape or sand it once dry, and its answers page adds that wiping does not clear glue from the pores. Glue left in the pores shows as a pale patch under a finish.

Leave it. Titebond's answers page says to clamp an unstressed joint for 30 minutes to an hour and not to stress a new joint for at least 24 hours (Titebond FAQs). The Wood Handbook adds that glues need hours to weeks to reach full strength. Take the clamps off after an hour or so, and do not plane, carry or load the tote until the next day.

Flushing the joints and fixing the bottom

Once the glue has had its day, plane the proud ends of dovetails and tenons flush with a sharp, finely set plane, working from the corner inward so the plane does not split off the last fibers. Planing a board square covers setting the plane fine.

The bottom goes on last, and without glue. It is nailed under the box with its grain running the length of the tote, so it can swell and shrink across its width. Physical principle Purdue Extension's furniture bulletin explains that a finish slows moisture exchange but does not stop it, and that wood has to be free to move across the grain (The Shrinking and Swelling of Wood, FNR-163). Noor's bottom is two pieces of 1x6 side by side with a hairline gap; Hal's is two 1x8 pieces with a 1/16 in gap. The gap leaves room for each piece to swell in a damp month. The movement calculator gives the figure for your wood and your room, and Choosing wood explains it. Finish the tote before nailing the bottom on if you want the inside faces finished too.

3. A finish for where it will live

A finish on a tote does three things: it keeps dirt and hand grease out of the grain, makes the surface easy to wipe, and slows the wood's exchange of moisture with the air. It does not stop that exchange. Purdue's bulletin is plain on this point, and it is why the bottom is still nailed to move. Physical principle

The default: dewaxed shellac, then paste wax

Shellac is a resin dissolved in alcohol. It dries as the alcohol evaporates, so it is dry in minutes, and brushes clean in denatured alcohol. Dewaxed shellac has had the natural wax removed, so anything can go over it later. We use Zinsser SealCoat as the example because its maker's sheet is current and complete (Zinsser SealCoat technical data, BEY-07, revised January 2024). Product-specific From that sheet:

  • It is 100 percent dewaxed shellac, compatible with any clear topcoat, and for interior use only.
  • Apply it between 50 and 90 F, below 85 percent relative humidity. Used as a sealer, it goes on straight from the can, unthinned.
  • On bare wood the first coat is dry to the touch in 5 to 10 minutes and can be sanded or recoated in 20 to 30 minutes. Sand lightly with 120 grit or finer after 45 minutes.
  • Clean brushes with denatured alcohol, or one part household ammonia to two parts water.
  • Its flash point is 55 F, so it catches fire easily; keep it away from flames and pilot lights. Its safety data sheet says to use it only with adequate ventilation and describes opening all doors and windows for cross-ventilation.

Two thin coats, a light sanding between them, is enough for a tote. Brush with the grain in long strokes and do not go back over a stroke that has started to dry. Vacuum or sweep the sanding dust rather than blowing it away: the U.S. National Toxicology Program lists wood dust as "known to be a human carcinogen" (Report on Carcinogens, 15th edition, 2021), mainly for nasal cancers among people exposed at work. No source we found measures the exposure from a few minutes of hand sanding.

After the shellac has dried, rub on a thin coat of paste wax, a soft wax that dries to a polish. Minwax's sheet says to let it dry 10 to 15 minutes and buff, and its label says the contents are flammable and to use it with adequate ventilation (Minwax Paste Finishing Wax). The wax gives a surface that sheds water drops and slides into a cabinet.

Alternatives, by where the tote lives

Where it livesA finish to considerThe maker's figuresRags
Indoors, dry (Noor's cabinet, Imani's caddy)Dewaxed shellac and paste wax (the default)Touch dry 5 to 10 minutes; sand after 45 minutesFollow each label
A garage or shed, damp hands, garden dirt (Hal)An oil and varnish blend, such as Watco Danish OilApply at 60 to 90 F; wipe off all excess after 15 minutes; touch dry 6 to 8 hours; 72 hours before any topcoatSealed, water-filled metal container
Hard handling, wiped oftenMinwax Wipe-On Poly (oil-based)Recoat after 2 hours; dry 24 hoursSealed, water-filled metal container
Indoors, where solvent smell is a problemMinwax Polycrylic (water-based)Recoat after 2 hours; soap and water cleanup; label still says "vapor harmful" and asks for open windowsFollow the label

The Watco figures are from Rust-Oleum's data sheet WAT-02, revised January 2026. An earlier sheet gave different recoat times, so check the date on yours. Dry and cured are different things: dry means ready for the next coat, cured means hard enough for daily use. General Finishes gives an average cure of about 21 days for water-based finishes and 30 days for oil-based ones (Dry time and cure time). A tote can be used gently once dry; it hardens over the following weeks.

Ventilation, heat and flames are on the label. Each finish and solvent states its own ventilation and fire precautions, and they differ. Denatured alcohol's safety data sheet, for one, says it is highly flammable, toxic if swallowed, and to be used only outdoors or in a well-ventilated area (Klean-Strip Denatured Alcohol SDS). Read the label of every can before you open it. Nothing here says a finish is non-toxic or safe for any use; that is the label's to state.

For finishes on the wood already in your home, such as cabinets and floors, Learn Home Finishes compares them, and the Finishes for a small piece page lists the ones above with their dates.

4. Oily rags, solvents and storage

Some finishes cure by reacting with oxygen in the air, and the reaction gives off heat. Linseed oil, Danish oil, oil-based polyurethane and oil-based stains all do it. Spread on a board, the heat escapes. Bunched in a rag, it builds up. The Piedmont, California, fire department warns that bunched rags can ignite without a spark or flame, and reports several such fires in its city in three years (Piedmont Fire Department, June 2026). Washington's State Fire Marshal, citing the National Fire Protection Association, puts the average at 1,700 home fires a year from spontaneous combustion of flammable and combustible liquids, at least 900 of them from rags (Washington State Patrol, March 2026).

Do what the label says, right after you use the rag. The labels we read agree on the method:

So keep a metal can with a tight lid, such as a clean paint can, half full of water, beside you when you finish with any oil. Push each rag under the water as you finish with it, close the lid, and take the can to your area's household hazardous waste collection, as the fire services say. The rag hazard follows the product, not the way it was put on: Minwax's wipe-on polyurethane carries the same warning as its stain. SealCoat's safety data sheet has no spontaneous combustion statement, but put its rags in the can anyway if any oil was used the same day.

Laying rags flat is not the same as the label method. A National Park Service fire prevention article describes a crew's linseed oil rag that was laid flat outdoors on a workbench and still caught fire and spread to a shed wall (Spontaneous Combustion: Fact or Fiction?). Some fire services describe drying rags flat outdoors before canning them; the labels we read say to put them in water right away. Follow the label of the product you used, and your local rules for disposal.

Solvents and finishes in a home

New Mexico State University's extension guide gives the household rules (Safe Use and Disposal of Household Chemicals, G-312): do not store chemicals on shelves used for food, do not put them in containers that look like food containers, keep them in their original containers and out of children's reach, and do not pour solvents or wood finishes down a drain. Washington's fire marshal adds: original containers, tightly capped. Finish where food is not prepared or stored. Imani's daughter June (fictional), 9, lives with her, so the cans, the alcohol and the rag can go on a high shelf in the basement, not under the kitchen sink. For cuts, burns or anything swallowed, call a doctor or emergency services; this manual gives no medical advice.

5. Mending a loose joint

The same glue and clamps that built the tote can mend a chair rung, a stretcher or a drawer joint that has worked loose. Most loose joints in household furniture are glue that has failed, often after years of the wood swelling and shrinking around it, and of the chair being rocked or dragged, which racks the joints. A stretcher (or rung) is the rail that runs between two chair legs low down to brace them.

What lasts, by one writer's ranking

Bob Flexner, a furniture refinisher and writer, ranks the ways to reglue a joint from least to most lasting (The Best Way to Reglue Furniture):

Method, least to most lastingFlexner's view
Metal fasteners: nails, screws, bracketsThey split the wood and do not tighten the joint
Injecting glue without taking the joint apartHolds about a year
Taking it apart and gluing over the old glueBetter, but new glue bonds only to the failed old glue
Hot hide glue over old hide glueWorks, because hide glue bonds to hide glue
Taking it apart, cleaning off all the old glue, regluingThe lasting repair

In a companion article he gives the method: remove any nails, screws or corner blocks first; knock the joint apart with a dead-blow hammer; clean the old glue off; reglue and clamp (Regluing Doweled Chairs). He also gives the test that tells you which glue you have. Hot water softens and washes off hide glue, and white vinegar softens white and yellow glue; scraping old glue tends to take wood with it.

The conservation view

Conservators start from a different question: what will this treatment do to the piece? A West Dean College conservation case study says dismantling should not be the default when the other joints are sound, the surfaces are fragile, or pegs, screws or nails hold the joint (A gentler approach to fixing your wobbly legs). On a set of pegged oak chairs where the first dismantling caused damage, the team treated the rest without taking them apart. So the two sources do not disagree about glue; they weigh the damage of taking a piece apart differently. Flexner's lasting method suits a sturdy everyday chair. Something old, fragile or valuable is a case for a professional.

Why hide glue for mending

A furniture conservator writing for the Building Conservation Directory describes hide glues as strong and reversible when in contact with moisture, while PVA (white and yellow glue) normally cures irreversibly (Adhesives for the Conservation of Fine Furniture). Reversible means the next person to mend the joint can soften the glue and take it apart without breaking the wood. The National Park Service notes that the hide and fish glues in older furniture are to varying extents soluble in water, which is why joints come loose when such furniture gets wet (Conserve O Gram 7/7). Preference For mending, our default is liquid hide glue.

Before you sand, scrape or strip old paint

Old painted furniture may carry lead paint. The federal ban in 16 CFR Part 1303 covers furniture with lead-containing paint manufactured after February 27, 1978. A piece made earlier may or may not have it; age raises the likelihood and does not decide it. EPA lists refinishing old furniture among the hobbies that can raise a family's lead exposure, and advises not sanding, or wetting the surface first if you must (Reduce the Risk from Lead Exposure in Your Home).

A home test kit does not settle it. In a 2007 study, staff of the Consumer Product Safety Commission found that of 104 test results from home kits, 56 were false negatives and two were false positives, and CPSC says consumers should not use the kits on products; testing by a qualified laboratory is the reliable route (CPSC, Home Lead Test Kits Unreliable). The kits EPA recognizes are for certified renovators and trained professionals (EPA, Lead Test Kits). Ask the authority A laboratory or a certified lead professional settles whether the paint has lead. Learn Home Finishes covers lead in older homes.

If you were thinking of stripping the paint: since November 22, 2019, federal rules have barred methylene chloride paint and coating removers from sale to consumers (EPA, Risk Management for Methylene Chloride). A broader 2024 EPA rule was struck down by a federal appeals court on September 15, 2026 (East Fork Enterprises v. EPA), and that ruling took effect on October 2, 2026. Neither affects the consumer ban, a law firm's note confirms (Crowell & Moring). Status as of November 10, 2026. EPA asks consumers to stop using any such product they already have.

The mend, step by step

  1. Record it first. On the mending sheet, write the piece, the joint, what moves, the paint or finish and its age.
  2. Settle the paint question before anything that makes dust or chips.
  3. Find out which glue it is. A drop of hot water on a hidden glue line: if the glue softens, it is likely hide glue (Flexner). White vinegar softens white and yellow glue.
  4. Decide whether to take it apart. If the joint comes apart with light blows and the other joints are sound, take it apart. If it would mean forcing tight joints, stop and consider a professional.
  5. Clean to bare wood, reglue, clamp, check square, and leave it 24 hours. Remove any nails or screws that were added to hold it. Do not add new ones through the joint.
Limits

A reglued chair is a seat. Nothing here says a repair will hold a person, and a fit test does not say it either. If you are unsure, ask a furniture restorer before anyone sits on it. Our judgment, not a source's, since no source we read states criteria: take the piece to a restorer when it is an antique or valuable, when veneer is lifting, when a part is broken rather than loose, when the joint carries a person's weight and you are unsure of it, or when paint that may contain lead would have to come off. For a rented home, what you may repair is in your lease; Learn First Home Basics covers repairs and requests.

Go deeper 6. Hot hide glue, food contact and injected repairs

Hot hide glue

Hot hide glue is the traditional form: dry granules soaked in water, then melted and kept warm. The Building Conservation Directory article describes preparing it by soaking, melting and simmering at 55 to 60 C, and names its weaknesses: poor gap filling, and brittleness with age. Old Brown Glue, a liquid hide glue sold as a gel, says to warm its bottle in a water bath, normally 110 to 160 F and best at about 140 F, and not to hold it above 180 F for long; it adds urea, which lowers the gel point from about 100 F to about 80 F (Old Brown Glue FAQ). For repairs it says hide glue bonds to old hide glue once that is reactivated, but bare wood is preferred. Flexner, for his part, prefers hot hide glue for repair and writes his method for white or yellow glue only because they are easier to work with.

Finishes and food

The tote is not a food surface, but the question comes up with every finish. The federal rule 21 CFR 175.300 lists the ingredients a food-contact coating may contain (linseed and tung oils and shellac among them) and limits what can be extracted from the finished film. It governs coatings' ingredients and performance; it does not certify any retail can or say anything about home application. When a maker says its product meets that rule, as Mohawk does for its Behlen salad bowl finish "in its cured state", that is the maker's claim. The Forest Products Laboratory's note on finishes for bowls and toys advises choosing a finish recommended for food, letting treated items dry thoroughly for several weeks, and asking the maker or an extension office (Finishes for Wood Bowls, Butcher Blocks and Children's Toys, 2013).

Injected repairs

Flexner gives injection about a year, because new glue bonds only to the failed old glue. The West Dean team injected cold-setting fish glue on purpose, through small holes drilled at 45 degrees, because their goal was the least harm to an old object, not the longest-lasting joint. It was a professional choice for a valuable set of chairs, not a shortcut for a household one.

7. See it See it

Fictional example

Hal's kitchen chair. Hal (fictional), 71, has a painted kitchen chair from the 1950s whose front stretcher is loose at both ends. The legs and seat joints are tight. He fills a row on the mending sheet before touching it.

Known: the stretcher moves in both legs; every other joint is tight; the paint is intact; the chair was made before 1978. Assumed: the glue is hide glue, which he will test with a drop of hot water on a hidden glue line under the seat; this is his assumption, from the chair's age. Open: whether the paint contains lead, which a laboratory or a certified lead professional settles, not a home kit; and whether the repaired chair will hold a person, which a furniture restorer settles if he is unsure.

He tries the stretcher. It slides partway out of one leg, but freeing the other end would mean spreading the front legs and forcing the tight seat joints. That is the West Dean situation: other joints sound. So he does not take the chair apart, and he does not sand, scrape or strip anything while the paint question is open. He arranges a lab test of a paint chip, taken the way the lab tells him to. If the paint is clear, the joint that slides out gets Flexner's lasting treatment: hot water to soften and wipe off the old hide glue, liquid hide glue, clamps, a check of the diagonals, 24 hours. For the stuck end, and for the chair as a seat, he will ask a restorer. He writes all of this on the mending sheet, so the next person who mends the chair knows what glue is in it.

8. Practice Practice

Minimum: one timed dry run of your tote with every clamp, then the glue-up, the diagonals checked, and two coats of shellac. Time: about an hour for the dry run and glue-up, a day for the glue, an evening for the finish and wax. Materials: the fitted tote parts, glue, four or more clamps with scrap pads, a damp cloth, a chisel, a story stick or tape for the diagonals, paper to cover the table, dewaxed shellac, denatured alcohol, a brush, 120 grit or finer sandpaper, paste wax, a soft cloth, and a lidded metal can half full of water.

  1. Rehearse. Dry-fit everything, ends with the handle and divider first, and time it. Split into two stages if it runs past the glue's total assembly time.
  2. Glue up. Thin glue on both surfaces, clamp to close, check the diagonals, and wipe the squeeze-out with a damp cloth or scrape it once dry.
  3. Wait a day, then flush. Plane the joints flush and sand lightly.
  4. Finish. Two thin coats of shellac with a light sanding between, then paste wax, buffed. Put rags in the can and the cans away.
  5. Fix the bottom and load it. Nail the bottom on with its gap, put the contents in, and tick off the build on the tote project sheet.
  6. Mend one household joint (Go deeper; optional). Fill a row of the mending sheet first, and settle the paint question before any dust.

9. Your setup Your setup

10. Check your work Check your work

Criteria

  • Did the dry run fit inside the glue's total assembly time, or did you split the glue-up?
  • Were the glue, the air and the wood above the glue's minimum temperature?
  • Are the diagonals equal, measured while the glue was wet?
  • Is every joint closed with no glue film showing in the gap?
  • Is the bottom nailed, not glued, with its grain along the length and a gap between pieces?
  • Did the finish go on in a ventilated room, and are the rags, cans and solvents put away by their labels?
  • For a mend: is the mending sheet filled in, and was the paint question settled before any dust?

Worked example

Noor (fictional) dry-runs her cleaning tote on her dining table, with paper over the veneered top. The ends, the handle and the divider go together first, then the two sides close into the rabbets. Her rehearsal takes 19 minutes, so she uses liquid hide glue (20 to 30 minutes total) and still splits it: ends, handle and divider one evening, sides the next. Her diagonals first differ by 1/8 in; she corrects them before the glue sets. The next evening she flushes the tenons, applies two coats of SealCoat with the kitchen window open and a fan in it, and waxes it the evening after. Her bottom is two pieces of 1x6 nailed under with a hairline gap. The tote passes every criterion. The one thing left open is noise: she did the clamping and planing before 8 p.m. and is still to ask the downstairs neighbor whether that is fine.

Common mistakes

  • Skipping the dry run. You notice it when the glue grabs before the last joint is closed.
  • Clamping a racked box. You notice it only if you measure the diagonals. Measure before the glue sets.
  • Gluing the bottom on. You notice it in the first dry winter, when the bottom splits.
  • Leaving an oily rag on the bench. You may not notice it until it is too late. Put the can out before you open the finish.
  • Screwing a loose chair joint. It splits the wood and does not tighten the joint, by Flexner's account.

What is still unresolved

  • Whether old paint contains lead: a laboratory or a certified lead professional.
  • Whether a mended chair will hold a person: a furniture restorer.
  • What a renter may repair or change: the lease; Learn First Home Basics.
  • How a finish behaves in your own room and wood: a test on an offcut, which the Finishes for a small piece page suggests.
  • Gaps in the joints that the glue-up showed: When it goes wrong, and Dovetails for a dovetailed corner.

11. Knowledge check and scenario

Your dry run takes 18 minutes and your glue's total assembly time is 10 to 15 minutes. What do you do?
Split the glue-up into stages (the ends, handle and divider first, the sides after the clamp time), or use a glue with a longer total time, such as liquid hide glue at 20 to 30 minutes. Do not try to beat the clock.
Your diagonals differ by 1/8 in with the clamps on. What does it mean, and when do you fix it?
The box is racked. Fix it now, while the glue is wet: ease the clamps, press the long diagonal's corners toward each other, retighten and measure again.
You finished with Danish oil. Where does the rag go?
Right away into a sealed, water-filled metal container, as Watco's data sheet and safety data sheet say, and then to household hazardous waste under local rules. Laying it flat is not the label's method, and a Park Service account describes a flat-laid rag that burned.
A kitchen chair from 1965 is painted and wobbly. What do you settle before sanding it?
Whether the paint contains lead. The federal ban covers furniture made after February 27, 1978, so a 1965 chair may carry it. A laboratory or a certified lead professional settles it; CPSC says consumers should not rely on home kits for products.
(Go deeper) Does a finish that meets 21 CFR 175.300 make a bowl food safe?
The rule governs a coating's ingredients and what can be extracted from the finished film; it does not certify a retail can or home application. A maker's claim that its product meets the rule is the maker's. FPL advises a finish recommended for food and several weeks of drying.
A friend's dining chair has one loose rung. Every other joint is tight, the chair is painted, and nobody knows its age. Your friend asks you to fix it this weekend. What do you do first?
Flexner ranks fasteners as the least lasting repair: they split the wood and do not tighten the joint. Drilling also makes paint dust from a finish whose lead content nobody knows.
This settles what can be known before anything irreversible happens. If the rung slides out and the paint is clear, clean and reglue it with hide glue. If it means forcing sound joints, that is the conservation case for leaving it or for a professional.
A sound choice if the chair is old, valuable or someone's daily seat and you are unsure. It costs money and time, and for a sturdy chair with one rung that slides out, the mend may be well within reach.

Checklist

Records your learning only; it is not a qualification.

Have you just done what this manual teaches? If it is still fresh, we would like to hear about it. We are looking for volunteer guides to add a few short passages from their own experience to this manual. Write to guides@learnthings.online for the details.