Make a bench hook this weekend
One pine board, a saw, a square and a pencil or knife make the first holding aid, on a kitchen table, with no workbench. The first square cut is made on the finished hook.
A bench hook is a flat board with a fence across each end, one on top and one underneath. The lower fence hooks over the table edge, you push the work against the upper fence, and gravity and the fence hold it while you saw. Popular Woodworking's maker puts it plainly: gravity and a solid fence are all it takes to keep the work from moving (Make a Pair of Bench Hooks, Zachary Dillinger, 2022). We follow his method: make one board, then saw it apart into a matched pair, so both fences sit in the same place. This page is the short route for the smallest setup: a kitchen or dining table, no tools yet, inches. Each step links the chapter with the reasoning.
What you need
| Item | What it does here | Where it is explained |
|---|---|---|
| One pine 1x8, about 24 in long | A 1x8 is 3/4 by 7 1/4 in actual size when dry, by the federal softwood standard. Pick the flattest, straightest board in the rack; the species is often not labeled, which does not matter for a bench hook | At the store |
| A saw | A ryoba (a Japanese pull saw with a rip edge and a crosscut edge) does both cuts on this page | The first tools, Sawing to a line |
| A square | A combination or try square, checked before it is trusted | Marking out |
| A pencil or a marking knife | A knife line gives the saw a groove to start in; a sharp pencil works for a first hook | Marking out |
| Wood glue and two clamps | Hold the fences on while the glue sets, and hold the board to the table while you saw it | Glue, finish and mending |
| A scrap board or a sheet of hardboard | Goes under everything, so the saw and the glue stay off the table | A shop on a table |
The article also nails each fence after gluing it, with the holes drilled first. Nails need a hammer and a drill. Hammering is loud: one agency's noise chart puts hammering at 94 to 97 dBA (How Loud Is It?, Workers' Safety and Compensation Commission). With neighbors below, we use glue and clamps alone on the smallest setup Preference. If you have a drill and the hour suits the building, nail as the article does.
A saw and a knife cut skin as readily as wood. Keep both hands behind the cutting edge, cut away from your body, and clamp the work rather than holding it in your hand when you saw down a long board. Put the knife and saw away where a child cannot reach them, as KidsHealth advises for household tools. For a cut that will not stop bleeding, call 911 (or your local emergency number); the American Red Cross and MedlinePlus say when a cut needs care. Nothing on this page certifies a method as safe.
First: check the square
Every line on this page is drawn with the square, so test it before the board comes home. This is the flip test, as Popular Woodworking's writers describe it (Measure, Mark and Lay Out, Robert W. Lang; All About Try Squares).
- Hold the square's stock against a straight edge and draw a fine line along the blade. The factory edge of a sheet of hardboard or a straight board will do; sight along it first.
- Flip the square over, set the same edge of the blade to the line, and draw a second line.
- Compare the two lines. If they coincide or run parallel, the square is square. If they spread apart, the gap is twice the square's actual error. A new square that fails goes back to the shop; filing one true is in Marking out.
Make the pair
Put the scrap board or hardboard on the table first. Saw with the board clamped so the cut hangs just past the table edge, not over the table itself.
- Cut the board to about 24 in. Square a line across it, start the saw on the waste side of the line, and let the saw do the work. The article turns a 24 in board into a pair with an 18 in working length; any length that suits your work is fine (Sawing to a line).
- Choose a reference edge and mark it. Pick the straighter long edge and draw a mark on it. Every square line from here on is drawn with the square's stock against that edge (Reference faces). The article planes this edge straight and square first, as practice; a store board is already surfaced, so on the smallest setup we skip planing and rely on choosing a straight board Preference.
- Cut a 2 in fence from each end. Square a line 2 in from each end and saw both off. Cutting the fences from the same board means they move with the seasons the way the base does, which is the article's reason for it (Choosing wood).
- Glue one fence across each end, on opposite faces. One fence goes on top at one end. Turn the base over and glue the other underneath at the other end. Set each fence square to the reference edge with the square, clamp it, and wipe off the glue that squeezes out. Titebond's maker says to clamp a joint that is not under stress for 30 minutes to an hour and not to stress a new joint for 24 hours (Titebond FAQ), so leave it overnight (Glue, finish and mending).
- Saw it in two along its length. Draw a line down the middle from the reference edge and rip along it with the rip edge of the saw. Starting the cut from both ends and joining them in the middle is easier for a first rip, the article says. If the cut drifts off the line, Why a cut wanders names the usual causes.
- Leave off the wax. Finish is optional, but the article says to avoid any wax, which would let the work slip.
The first square cut, on the finished hook
This is the cut the hook exists for, and the check that it works.
- Hook one bench hook over the table edge, lower fence against the edge. With a long piece, use both hooks side by side.
- Square a line round a scrap of the same board: across the top, down both edges, across the bottom. The line should meet itself where it started (Marking out).
- Hold the scrap against the upper fence with the waste side of the line hanging past the end of the hook. A right-handed sawyer usually works with the waste to the right; mirror it if you are left-handed.
- Start the cut on the waste side of the line with short, light strokes, then lengthen them. Keep your eye over the blade and saw down to the hook's surface without pressing.
- Check the cut with the square on the face and on the edge. A gap under the blade means the cut leaned. Write what happened in the practice log.
Done when: the pair of hooks sits flat on the table without rocking, a scrap held against the fence does not slide while you saw, and one crosscut on it meets its line on both faces when checked with the square.
Noor (fictional) rents a third-floor apartment with neighbors below and works on a 30 by 48 in dining table with a veneered top. She buys one pine 1x8, labeled "common board" with no species, and a ryoba, a combination square, a pencil, glue and two clamps.
Known: the board is 3/4 by 7 1/4 in, the table is veneered, and the square passed the flip test on the hardboard's factory edge. Assumed: a sheet of hardboard under the work will keep saw marks and glue off the veneer; she checks the hardboard's underside after each session. Open: whether the downstairs neighbor would mind hammering after 8 p.m. She glues and clamps the fences instead of nailing them, so the question waits until she chops mortises, and she settles it then by asking.
Her first crosscut on the finished hook leans: the square shows a gap on the edge. She writes it in the practice log, saws three more on scrap, and the fourth meets its line on both faces.
The three chapters to open next
- A shop on a table: the rest of the holding kit (a planing board hooked on the table edge, and clamping over a leg for chopping), protecting the top, noise and neighbors, and where the edge tools live.
- Sawing to a line: rip and crosscut teeth, the knife wall, staying on the waste side, and what to check when a cut wanders. Five square cuts in a row on the hook is that chapter's own measure of done.
- Measuring without numbers: the tote starts here, with the things it will carry laid against a story stick.
What this page is not telling you
- Skipping the planing is our adaptation. The article flattens the face and squares the edges first, as practice in accurate work. A hook from an unplaned store board works; it is less accurate than one made the article's way, and Planing a board square is the long version.
- Glue without nails is our choice for a quiet flat, not the article's method.
- A bench hook can also serve as a shooting board for trimming ends, Popular Woodworking's Christopher Schwarz notes; Planing a board square covers that use.
This page is a route, not a full method: it skips the reasoning on purpose, and each link goes to the chapter that has it. It does not judge whether your table is sturdy enough for sawing; a table that rocks, folds or has a glass top is not a surface for this work, and A shop on a table says what to do instead. It gives no prices, and it does not say a cut, a tool or a setup is safe.