Choosing wood: species, boards at the store and how wood moves
Choose a species your tools can work, read nominal and actual sizes, pick a straight board, and work out how much it will move with the seasons.
Start here Essentials
At minimum, this chapter asks you to buy one or two softwood boards, read what they really measure, choose straight ones, and let them sit in the room you will work in. Everything marked Go deeper is optional on a first pass.
- Choose pine or yellow-poplar for a first tote. Both are soft enough for a new saw and chisel and sold at most home centers (Which wood for a tote).
- Read the label as a nominal size. A 1x6 is 3/4 by 5 1/2 in once dry; buy by the actual size (Sizes at the store).
- Pick the straightest board. Sight along each edge and face, then read its end grain (At the store, Grain).
- Store it flat, indoors, in the room you will work in. Check it again for straightness before you cut (Letting a board settle).
Minimum time: about an hour at the store and 10 minutes at home, then at least a week of waiting. Done when: the board is home, its actual size and species (or "unknown") are on the Tools and wood sheet, and it lies flat on the table.
1. Grain: how a board is built Understand
Wood is grown, not made. A tree adds a layer of new wood under its bark each season, and each layer shows on the end of a log as a ring. Along the trunk, the wood is a bundle of long, hollow cells lying side by side. Grain is the direction those cells run. In a board, it runs along the length.
Two facts follow, and the rest of this chapter rests on them. First, wood is strong and stable along the grain and weak and changeable across it. Second, wood takes up and gives off water from the air all its life, and when it does, it swells and shrinks across the grain far more than along it. Physical principle The Wood Handbook, the Forest Products Laboratory's reference, puts lengthwise shrinkage from green to oven-dry at 0.1 to 0.2 percent for normal wood, against several percent across the grain (Wood Handbook, chapter 4).
Across the grain there are two directions, and they differ too. Radial runs from the center of the tree out to the bark, across the rings. Tangential runs along the rings, parallel to the bark. The Handbook says tangential shrinkage is about twice radial shrinkage. That ratio is why the way a board was sawn from the log matters.
Reading the end of a board
The end of a board shows you which way it was sawn. Look at the rings on the end, and at the angle they make with the board's wide face.
- Flatsawn (also called plainsawn, or flat-grained in softwoods): the rings run more or less across the end, parallel to the wide face or in a shallow arch. The face shows the cathedral pattern of arches. Its width moves tangentially, the larger amount.
- Quartersawn (edge-grained or vertical-grained in softwoods): the rings run up and down on the end, close to square to the wide face. The face shows straight, parallel lines. Its width moves radially, the smaller amount.
- Rift-sawn or mixed: the rings cross the end at a diagonal. Most home-center boards are flatsawn or mixed.
The Handbook's commercial definition calls rings at 0 to 45 degrees to the wide face flatsawn and 45 to 90 degrees quartersawn, and says quartersawn boards shrink and swell less in width, cup less, and split less (Wood Handbook, chapter 3). Robert Lang's Popular Woodworking article reads the same three classes from the end grain and names plainsawn boards as the ones most likely to warp, twist and cup (Using grain pattern to choose lumber).
One more thing to find on the end: the pith, the small dark spot at the very center of the rings. A board with the pith in it holds the tree's center, where the rings are tightest curved, and it is prone to cracking and twisting as it dries. If you can see a complete small circle of rings on the end, the pith is in that board.
Grain direction also decides how a part is laid out. On the tote, the sides, handle and bottom have their grain running the length of the tote. The divider has its grain running along its own length, so it moves in height, as the sides do. The ends depend on the corner joint: through dovetails need the ends' grain running across, so each end is cut from a board as wide as the end is tall; on the rabbet path the ends may have their grain running up and down, so a narrow board can make a tall end. Measuring without numbers and Housings and rabbets take this up where the parts are sized and cut.
The definitions of quartersawn disagree. The Wood Handbook uses 45 to 90 degrees for quartersawn and says 30 to 60 degrees is sometimes called bastard sawn. Shannon Rogers, in Popular Woodworking, gives 60 to 90 degrees as the "official specification" and says buyers want 80 to 90 (Lumberyard prep). Glen Huey treats 30 to 60 degrees as rift-sawn. For a tote, the label matters less than the angle you can see: the closer the rings run to square with the face, the less the width moves.
Quartersawn wood still moves. It moves about half as much in width and more in thickness, because its thickness now runs tangentially. Rogers notes the thickness movement and the lack of cupping. "Quartersawn doesn't move" is not what either source says.
2. Which wood for a tote
For a first tote, choose a wood your tools can cut cleanly while you are learning to sharpen and saw, and one you can buy near you. Softer woods forgive a slightly dull edge; harder woods hold crisper corners and resist dents. The usual measure of hardness is the Janka figure: the force needed to press a steel ball 0.444 in across halfway into the wood, measured at 12 percent moisture (Janka hardness, The Wood Database). A higher number is a harder wood.
| Wood | Where sold | Janka (lbf) | By hand | Tangential coefficient (Table 13-5) |
|---|---|---|---|---|
| Eastern white pine | Home centers (when labeled), lumberyards | 380 | Easy to work by hand | 0.00212 |
| Big-box "pine" or "common board", species not labeled | Home centers | Unknown | Varies with the species you actually got | Unknown; the calculator's "not sure" row uses the largest listed, 0.00376 |
| Yellow-poplar | Home centers, lumberyards | 540 | Very easy; can leave fuzzy surfaces | 0.00289 |
| Northern red oak | Home centers, lumberyards | 1,220 | Works well; moves more when flatsawn | 0.00304 |
| Black cherry, black walnut | Lumberyards, by the board foot | Not in our sources | Hardwoods, worked by hand at lumberyard sizes | 0.00248 (cherry), 0.00274 (walnut) |
Janka figures and working notes: The Wood Database pages for eastern white pine, yellow-poplar and red oak. Coefficients: Wood Handbook Table 13-5, explained under Moisture and movement. The full table is Woods for hand tools.
Our default for a first tote is pine or yellow-poplar. Preference Both cut easily with a new saw and a freshly sharpened chisel, both are sold in 3/4 in boards at home centers, and both cost less than a hardwood, so a spoiled part is cheap to replace. Red oak is harder and works well, but The Wood Database calls its dimensional stability "mediocre", especially flatsawn, and wet oak stains black where it touches iron. Cherry and walnut are lovely to work and are a lumberyard purchase, which brings in the hardwood sizes and board feet below.
Big-box "pine" is a species you do not know
Many home centers sell a board labeled only "pine", "common board" or "select pine". It is often not eastern white pine, and we found no source that says what species it usually is. Treat its species as unknown unless the label or the grade stamp names one. That has two practical effects. Its hardness and working qualities are whatever you find with your tools, so a test cut on an offcut tells you more than a guess. And its movement figure is unknown, so the movement calculator handles it with a cautious "not sure" choice, explained below. Write "unknown" in the species column of the wood sheet rather than guessing.
Dust and reactions
Some woods bother some people. The Wood Database lists reported reactions by species: eastern white pine can cause skin reactions or asthma-like symptoms in some people, yellow-poplar is listed as an irritant, and oak as an irritant and sensitizer. The same page says very few woods are toxic in themselves, and that all inhaled wood dust is hazardous to long-term health (Wood allergies and toxicity). Planes and saws make shavings and coarse chips more than fine dust; sanding makes the fine dust. If a wood gives you a rash, a runny nose or a tight chest, stop working it and ask a doctor. Ask the authority
3. Sizes at the store
The size printed on a softwood board is its nominal size, a name. The board you take home is smaller: its actual size. The American Softwood Lumber Standard, PS 20-25, published by NIST, sets the dry sizes: a nominal 1 in board is 3/4 in thick, and nominal widths of 2, 3, 4, 6, 8, 10 and 12 in are 1 1/2, 2 1/2, 3 1/2, 5 1/2, 7 1/4, 9 1/4 and 11 1/4 in dry (PS 20-25, NIST). Convention A 1x6 is 3/4 by 5 1/2 in. A 2x4 is 1 1/2 by 3 1/2 in. "Dry" in the standard means dried to 19 percent moisture or less, which is wetter than a heated room, a point that comes back under Moisture and movement.
Length is the exception: a board sold as 6 ft is usually at least 6 ft long, and often a little more. Measure it anyway, and plan on cutting off an inch or two at each end, where checks (small end splits) and dents collect.
Hardwood is sold another way
At a lumberyard, hardwood is sold by thickness in quarters of an inch, in random widths and lengths. A 4/4 ("four-quarter") board is about 1 in thick rough, straight from the sawmill. Planed on both faces, called S2S (surfaced two sides), it is 13/16 in thick. The Wood Handbook's table gives 5/4 as 1 1/4 in rough and 1 1/16 in S2S, and 8/4 as 2 in rough and 1 3/4 in S2S (Wood Handbook, chapter 6). Convention S4S means all four sides planed, with square edges.
Hardwood is priced by the board foot: 144 cubic inches, a piece 1 in thick, 12 in wide and 12 in long (Virginia Department of Forestry). PS 20-25 computes softwood board feet from the nominal sizes: thickness in inches times width in feet times length in feet. The hardwood trade tallies at the rough thickness, and the Handbook tells buyers to say which sizes they mean. Ask the yard how it counts before comparing prices. Ask the authority The boards calculator shows both counts.
Grades in a sentence each
Hardwood grades come from the National Hardwood Lumber Association's rules and rate how much clear wood a board yields in usable pieces, judged on the poorer face (AHEC, the grades). Convention
- FAS (firsts and seconds): boards 6 in and wider, 8 ft and longer, at least 83 1/3 percent clear in usable cuttings. The top grade.
- Selects: like FAS on the better face, in narrower and shorter boards.
- No. 1 Common: 3 in and wider, 4 ft and longer, at least 66 2/3 percent clear. For a tote's short parts, Common boards can yield all the clear wood you need for less money.
Softwood boards at a home center carry their own names ("common board", "select" or a grade stamp) under different rules. For a tote, the board in your hands decides more than the grade on the rack.
The grading rules in full. The NHLA rule book is sold, not published free, so our figures come from the Wood Handbook's Table 6-1, the American Hardwood Export Council and Ohio State Extension. They agree on FAS and No. 1 Common. They differ on Selects: the Handbook and AHEC give 4 in and wider and 6 ft and longer, while Ohio State's fact sheet gives 3 in and 4 to 16 ft. Ohio State also gives No. 2 Common (half clear) and No. 3 Common (a third clear). F1F (FAS one face) is FAS on one face and No. 1 Common on the other.
4. At the store: picking a board
Take your cut list or a rough idea of the parts, a pencil, and if you have one, a short straightedge or a square. A tape helps with lengths. At a home center, you are free to look through the rack and choose; put back what you do not take, flat and squared up as you found it.
A board can be out of shape in four ways. Each has a name you will meet again in Planing a board square.
| Defect | What it looks like | How to see it | Matters for a tote? |
|---|---|---|---|
| Bow | The face curves along the length, like a ski | Lay the board on the floor face down, or sight along the face | A little is fine in short parts; parts cut short lose most of it |
| Crook | The edge curves along the length | Sight along the edge from one end | Costs width when you straighten the edge; avoid in a narrow board |
| Cup | The face curves across the width, like a trough | Look at the end, or rock a straightedge across the face | Costs thickness to plane out; avoid more than a slight cup |
| Twist | The corners do not lie in one plane; the board rocks on two corners | Lay it on the floor and press each corner, or sight along it | The hardest to remove by hand; avoid it |
Then look at the faces and ends for the faults that are not about shape: knots (where a branch grew; a loose or black-ringed knot can fall out), splits and checks (cracks, usually at the ends), wane (bark or a rounded edge where the board ran out of tree), and the pith on the end. A tight knot in a part that will not be cut through, such as the middle of the bottom, is fine. A knot where a joint goes is trouble.
- Sight along each board. Hold one end at eye height and look down the edge, then the face, toward good light. Bow, crook and twist show as a line that does not stay straight. Rotate the board and look again.
- Read the end. Look for the pith, the ring pattern and any end split. Prefer rings that run steeply across the end and boards without the pith. Lang's article and the Handbook both name the flatsawn, cathedral-faced board as the one most likely to cup.
- Find the straightest grain for the handle. The handle is long and narrow and carries the load. Look on the edge and face for grain lines that run parallel to the edge for its whole length, without running out to the side. Straight-grained stock for parts that must stay straight is Rogers' advice too.
- Buy enough. Add up the parts with an allowance for rough cutting. Glen Huey's Popular Woodworking article suggests cutting parts about 1 in over length and 1/4 in over width first, then to final size later (Why wood warps). Convention Leave extra for a bad end and a knot in the wrong place. The cut list calculator totals the length you need with the allowance and the saw kerf; the boards calculator checks whether those parts fit the boards you plan to buy.
At home, write each board on the Tools and wood sheet: species or "unknown", nominal size, actual size, length, where bought and the date it came home.
5. Moisture and movement
A living tree is full of water. Some fills the cell cavities, called free water, and some is held inside the cell walls, called bound water. As wood dries, the free water leaves first. The point where the cavities are empty and the walls still full is the fiber saturation point, about 30 percent moisture content for most species (Wood Handbook, chapter 4; Oregon State Extension EM 8600). Physical principle Above it, wood does not change size as it dries. Below it, wood shrinks as the walls give up water and swells as they take it back. Moisture content is the weight of water in the wood as a percentage of the wood's oven-dry weight.
Wood settles to match the air
Wood kept in air of steady temperature and humidity settles to a moisture content that matches it, its equilibrium moisture content (EMC). Relative humidity matters far more than temperature. The Wood Handbook's Table 4-2 gives, at 70 F:
| Relative humidity at 70 F | 20% | 30% | 40% | 50% | 60% | 70% | 80% |
|---|---|---|---|---|---|---|---|
| Equilibrium moisture content (%) | 4.5 | 6.2 | 7.7 | 9.2 | 11.0 | 13.1 | 16.0 |
The Handbook notes that the decimal place is for illustration, not precision. Indoors, the air dries out in a heated winter and dampens in summer, so wood indoors swings through a range every year. For interior woodwork and furniture, the Handbook's Table 13-2 gives an average of 8 percent with individual pieces at 6 to 10 percent for most of the US, 6 percent (4 to 9) in the dry Southwest, and 11 percent (8 to 13) on the damp, warm coasts (Wood Handbook, chapter 13). Physical principle An unheated garage or an outdoor shed sits wetter. A board labeled dry under PS 20-25 can be as wet as 19 percent, and Woodcraft notes that softwood is often kiln dried to 12, 15 or 19 percent and needs further conditioning for interior use (WoodSense: acclimating wood).
How much a board moves
The Wood Handbook gives a way to estimate how much a board's width changes between two moisture contents (chapter 13, Equation 13-3):
Change in width = width × coefficient × (final moisture content − starting moisture content)
The coefficient comes from Table 13-5, per 1 percent change in moisture content: the tangential coefficient for a flatsawn board, the radial one for a quartersawn board. When you are not sure how a board was sawn, the Handbook's chapter 4 says to use the tangential value.
A worked case: a 5 1/2 in wide eastern white pine board, flatsawn (tangential coefficient 0.00212), indoors in most of the US, going from 6 percent in winter to 10 percent in summer. 5.5 × 0.00212 × (10 − 6) = 0.047 in. That is a little under 1/16 in. The same width in yellow-poplar (0.00289) changes about 0.064 in.
The estimate has three limits, and the Handbook states each. It is valid only between 6 and 14 percent moisture content. The linear method underestimates the true change by about 5 percent. And the coefficients are averages: chapter 4 puts the variation in shrinkage between pieces at about 15 percent. The movement calculator does the arithmetic, refuses to give a figure outside 6 to 14 percent, and reminds you of the 5 percent.
The movement figure is an estimate from species averages, not a measurement of your board, and it holds only between 6 and 14 percent moisture content. It tells you the size of change to design for; it does not tell you that a joint, a bottom or a finish will hold through a dry winter. For an unknown species the figure is only as good as the cautious coefficient behind it. Whether an old or valuable piece can take a repair that restrains its movement is a question for a furniture restorer.
What movement means for the tote
Wood moves across the grain whatever finish you put on it. Purdue Extension's furniture bulletin says finishes slow the exchange of moisture and do not stop it, and its advice is to design so the wood is free to move across the grain (Purdue FNR-163). Penn State Extension describes a table built from 6 percent stock, stored a year at about 13 percent, then moved into a forced-air heated house at about 4 percent, where the top moved and jammed the drawer (Understanding equilibrium moisture content).
The tote's design gives each part room:
- The bottom is the widest single part, with its grain along the length of the tote. It is nailed under the box rather than glued, so it can grow and shrink across its width. A bottom wider than one board is two or more boards nailed side by side with a small gap.
- The divider runs the length of the tote with its grain along its own length, and sits in slots in the ends that let it grow and shrink in height.
- The sides and handle run lengthwise, where wood barely moves.
- The ends on the rabbet path, grain up and down, change in width (across the tote) but hardly in height, while the sides they meet change a little in height. Fine Woodworking's rabbet article advises that the two pieces of a rabbet joint have their grain running the same way, except in plywood (All about rabbet and dado joints). Upright-grain ends depart from that. On a 4 1/4 in high side, indoors, the mismatch is small: about 0.064 in at the cautious coefficient. The rabbet path accepts it so that a narrow board can make a tall end; through dovetails, with all grain running across, do not have it. Test it
Letting a board settle
Wood bought from an outdoor rack or a cold warehouse is usually wetter than your room. As it dries to the room, it shrinks and can bow or cup a little. Better that it does this before you cut and plane it than after.
Our default: bring the board into the room where you will work it, lay it flat on a level surface with thin strips of scrap (stickers) under it every foot or so so air reaches both faces, and leave it. Then sight along it again before you cut. If it has moved, choose your parts around the movement. Sources disagree on how long. Huey suggests seven to 10 days; Purdue Extension says moisture change takes a few weeks to a month or more and that thin boards change faster than a stack (Purdue FNR-403). Convention For a 3/4 in board on its own, a week in the room and a straightness check is a reasonable floor; longer does no harm.
A moisture meter is optional. Pin meters read the electrical resistance between two pins, need correcting for species and for temperature (about 0.5 percent per 10 F away from the calibration temperature, says the Handbook's chapter 13), and read best below about 30 percent. Pinless meters read mostly the surface layers. For a board of unknown species, a meter's reading is itself an estimate. The waiting and the straightness check do the work without one.
The formula against the 2 percent rule. Purdue's FNR-163 offers a blanket rule instead of a species formula: allow 2 percent movement, which it equates to about an 8 point moisture change (for example 4 to 12 percent). On a 5 1/2 in board that allows 0.11 in. The Handbook's formula for eastern white pine from 6 to 10 percent gives 0.047 in. The rule is simpler and more cautious; the formula is species-specific and limited to 6 to 14 percent. The Wood Database adds that green-to-dry shrinkage is only a guide to movement in service: basswood shrinks a lot from green yet moves relatively little once dry (Dimensional shrinkage).
The Handbook's own caution about real boards. Chapter 13 says the method overestimates width change for commercial lumber that is neither truly flatsawn nor quartersawn, and underestimates thickness change. A mixed-grain board moves somewhere between its tangential and radial figures.
Acclimation advice compared. Huey: seven to 10 days in the shop. Purdue FNR-403: a few weeks to a month or more. Woodcraft: keep scrap in the room for several months and measure it to learn your local moisture content. The Handbook gives uptake rates instead: kiln-dried 8 percent stock piled outdoors in humid weather gains about 2 percent a month at first, in a closed shed about 0.3 percent a month.
Yellow-poplar's figures differ. The Handbook and The Wood Database give yellow-poplar 4.6 percent radial and 8.2 percent tangential shrinkage, green to oven-dry; Purdue's appendix gives 4.0 and 7.1. The calculator uses the Handbook's Table 13-5.
Target moisture content. Purdue FNR-403 says hardwood for furniture is kiln dried to 6 to 8 percent, midway between indoor extremes, and FNR-163 notes many furniture makers prefer about 6 percent because swelling closes joints while shrinking opens them.
6. See it See it
Noor (fictional) buys wood for a cleaning tote. Noor works on her dining table in a third-floor apartment and is building a tote to slide under her kitchen sink. Her parts come from Measuring without numbers: two sides 10 3/4 in long by 4 1/4 in, two ends 10 1/2 in tall by 7 1/4 in with their grain up and down (she is on the rabbet path), a divider 9 3/4 in long, a handle 10 3/4 in long, and a bottom of two pieces 10 3/4 in long by about 4 1/8 in.
At the home center she finds 1x6 boards labeled "common board", with no species on the label or the stamp. She sights along a dozen, rejects two with twist and one with the pith on the end, and takes two 6 ft boards with the straightest edges. The cut list calculator flags her ends: at 7 1/4 in wide they are wider than a 1x6, so she adds a 2 ft 1x8 (3/4 by 7 1/4 in) and will cut both ends from it with the grain running up and down. With Huey's allowance of about 1 in over length, the two ends need 23 in of that board, so she checks both of its ends for splits before buying. The rest of the parts need a little under 6 ft of 1x6; the second board covers a bad end, a knot, and the practice pieces. By PS 20-25's nominal rule she has bought 6 board feet of 1x6 and about 1 1/3 of 1x8. At home she writes all three boards on the wood sheet as species "unknown", with nominal and actual sizes, and stickers them flat on her kitchen floor for a week.
For movement, she uses the calculator's "not sure" row, the largest tangential coefficient it lists (white oak, 0.00376). Her widest parts are the ends, 7 1/4 in across the grain, which run across the tote's width. Indoors in a most-of-the-US climate, 6 to 10 percent: 7.25 × 0.00376 × 4 = 0.109 in, about 7/64 in between driest and dampest, and perhaps 5 percent more by the Handbook's note. If the boards were eastern white pine, the figure would be about 0.061 in. Each 4 1/8 in bottom piece changes about 0.062 in by the cautious figure, or 0.035 in as eastern white pine; nailed side by side with a hairline gap, they can.
Known: the boards' actual size and the climate band. Assumed: that a week flat in her kitchen has let the boards settle; she has no meter, so this is her assumption, checked only by sighting along them again before cutting. Open: the species, which no source can settle from the label. A label or stamp that names it, or someone who can identify wood, would settle it; until then the cautious figure stands.
Hal (fictional) and a garage. Hal's garden tote lives in his unheated attached garage. He buys yellow-poplar 1x8 (3/4 by 7 1/4 in) for the sides and a 1x10 (3/4 by 9 1/4 in) for the ends, because his dovetailed ends need their grain running across and stand taller than a 1x8 is wide. For the garage he uses Table 13-2's exterior band for most of the US, 9 to 14 percent: 7.25 × 0.00289 × 5 = 0.105 in, about 3/32 in, on each side. Open: the garage's real humidity, which a hygrometer (Purdue suggests an inexpensive one) would settle.
- Using grain pattern to choose lumber, Popular Woodworking (Robert Lang): the three end-grain classes with photographs.
- Why wood warps, Popular Woodworking (Glen Huey): why boards bow and cup, and the rough-cutting allowance.
- Wood Handbook, chapter 13, Forest Products Laboratory: the movement equation, the coefficients and the regional moisture table, free.
- Understanding equilibrium moisture content, Penn State Extension: a short video with a transcript and the jammed-drawer case.
7. Practice Practice
Minimum: one board chosen at a store by sighting and reading its end, written on the wood sheet, and stickered flat in your work room. Time: about an hour at the store, 15 minutes at home, a week of waiting, and 10 minutes for the recheck. Materials: your rough parts list, a pencil, a tape, a few strips of scrap for stickers, and a phone or notebook for the label details.
- Read five ends before you choose. At the rack, pull five boards and sort them by the end grain: flatsawn, quartersawn, mixed, and any with the pith. Notice which shows the cathedral pattern on its face.
- Sight each board. Rate each for bow, crook, cup and twist. Choose the straightest, preferring steep rings and no pith.
- Record the label. Write the nominal size, any species or grade stamp, and the price. Measure the actual thickness and width at home and write them on the Tools and wood sheet.
- Work out its movement. In the movement calculator, enter the species (or "not sure"), the grain you read on the end, the width, and the range for where the tote will live. Write the figure next to the board.
- Sticker it and recheck. Lay it flat on stickers in the work room. After a week, sight along it again and tick "straight on recheck" if it still is.
- Compare with the 2 percent rule (Go deeper; optional). Work Purdue's 2 percent allowance for the same width and compare it with the calculator's figure.
8. Your setup Your setup
9. Check your work Check your work
Criteria
- Can you say which way the rings run on the end of your board, and whether the pith is in it?
- Is the actual size, not only the nominal one, on the wood sheet?
- Is the species written down, or "unknown" when the label does not name it?
- Did the board pass a sighting for bow, crook, cup and twist, at the store and again after settling?
- Do you have a movement figure for the widest part, with the moisture range it assumes?
Worked example
Imani (fictional) buys 4/4 cherry, S2S, at a lumberyard for an art caddy: 13/16 in thick, random widths. Her basement has a dehumidifier holding about 55 percent humidity, which Table 4-2 puts at about 10 percent moisture content at 60 to 70 F. She reads the ends, chooses two boards with steep rings for the sides, and writes the species as black cherry, a fact the yard's tag gives her. Her one open question is the price: she assumes the yard tallies board feet at the rough 1 in thickness, and she asks at the counter. Her board passes every criterion, and the answer to the tally question goes on the wood sheet.
Common mistakes
- Buying by the nominal size. A cut list written for 6 in wide parts will not fit a 1x6. Notice it when a part's width on the list is larger than the board's actual width.
- Choosing by the face alone. A handsome cathedral face is the board most likely to cup. Read the end too.
- Guessing the species. Writing "white pine" for an unlabeled board gives a movement figure that looks precise and is not. Write "unknown".
- Cutting the day you get home. Parts cut from a board that is still drying can bow after you have planed them.
- Gluing a wide bottom in all round. A bottom fixed on all four edges cannot move and may split or push the box apart. Notice it in the plan before glue-up.
What is still unresolved
- The sizes of the parts, taken from the things the tote will carry: Measuring without numbers.
- Flattening and squaring the board you chose: Planing a board square.
- How the bottom is fixed so it can move, and the finish: Glue, finish and mending.
- The species of an unlabeled board: only a label, a stamp or someone who can identify wood settles it.