Housings and rabbets: the divider and the simplest strong corner
Lay out a housing from the part that goes in it, saw and pare it to depth, cut a rabbet for a simple corner, and fit both by paring rather than force.
Start here Essentials
At minimum this chapter asks you to cut one housing in a scrap and fit a scrap divider into it. Do it on the bench hook, on a scrap of the board you will build with. Everything marked Go deeper is optional on a first pass.
- Knife the divider's thickness across a scrap, using the divider itself. Stand the divider on the scrap and knife along both of its faces (Laying out from the part itself).
- Gauge the depth at about a third of the thickness. In 3/4 in stock that is 1/4 in, on both edges of the scrap (How deep).
- Saw both walls to the gauge line. Start each cut in a knifewall on the waste side (Sawing, chopping and paring).
- Chop and pare the waste to the line. Work in from both edges with the chisel bevel up, then pare the floor flat (Sawing, chopping and paring).
- Test the fit, and pare the part, not the joint, if it is tight. A shaving off the divider's face is the usual fix (Fitting by paring).
Minimum time: about an hour for the first housing. Done when: a scrap divider slides into the housing with hand pressure and stands square to the board.
1. Two joints, and where each goes on the tote Understand
A housing is a flat-bottomed groove cut across the grain of a board to hold the end of another board. American woodworkers usually call it a dado; British ones say housing, or housing dado. A rabbet (rebate in Britain) is a step cut along the edge or across the end of a board, so that it is open on one side. Both have the same three parts: two walls (a rabbet has one, called the shoulder), and a floor, the flat bottom of the cut. Fine Woodworking treats them as one family of joints and gives them the same depth convention (Fine Woodworking, All About Rabbet and Dado Joints).
What each one does comes from its shape. A housing traps the part on two faces and its floor, so the part cannot slide along the board and it is located exactly where you put the groove. A rabbet traps the part on one face and its floor. It locates the part and gives glue and nails more to bear on than a plain butt joint, but it relies on glue, nails or both to hold the parts together.
On the tote, the two joints do two different jobs:
- The divider sits in housings. It runs whichever way your contents need, and it is housed in the pair of walls it meets. A divider that runs the length of the tote is housed in the two ends; a divider across the width is housed in the two sides. All three totes in this manual have a lengthwise divider, because the handle runs the length of the tote over the divider: tall things stand beside the handle, not under it. A housing is cut across the grain of the wall it is in. In an end whose grain runs up and down, the same slot runs with the grain, and is strictly a groove; it is cut with the same saw and chisel.
- The divider's slot stops short of the top. The ends stand taller than the divider, so the slot runs from the bottom edge, which the tote's bottom covers, up to the divider's height, and stops. A slot that ends inside the board is stopped; one that runs from edge to edge is through.
- On the simpler path, the corners are rabbets. Each side has a rabbet across each end, on its inside face, and the end of the tote sits in it. The sides are then glued and nailed or pinned to the ends. The standard path, through dovetails, has its own chapter: Dovetails.
A rabbeted corner lets you choose the grain direction of the ends. Through dovetails need the grain of all four walls running along the wall, so a dovetailed end has to come from a board as wide as the end is tall. A rabbeted end does not: its grain may run up and down. That lets a narrow board make a tall end, which is why Noor's ends, 10 1/2 in tall, come from a 1x8 only 7 1/4 in wide. Choosing wood explains why grain direction decides which way a part moves.
| Housing (dado) | Rabbet | |
|---|---|---|
| Shape | Groove with two walls and a floor, across the grain | Step with one shoulder and a floor, at an edge or end |
| On the tote | Holds the divider in the pair of walls it crosses | The corners on the simpler path: each side's ends, inside face |
| Depth convention | About one-third of the stock, not more than half | About one-third; in 3/4 in stock at least 1/4 in and not more than 1/2 in |
| In 3/4 in stock | 1/4 in deep, as wide as the divider is thick | 1/4 in deep, as wide as the end is thick |
| What holds it | Its two walls locate the part; glue holds it in | Its shoulder locates the part; glue and nails hold it |
| Tools | Knife, square, gauge, saw, chisel, mallet; router plane optional | Knife, square, gauge, saw; chisel to clean up |
Depths in the table are Fine Woodworking's convention, set out in the next section. Which joint where sets these two beside the other joints in the manual.
2. How deep: the one-third convention
Convention Fine Woodworking's rule for both joints is a depth of about one-third of the thickness of the board being cut. For a rabbet in 3/4 in stock it sets a floor of 1/4 in and a ceiling of 1/2 in. For a housing it says one-third, and not more than half (Fine Woodworking). In the 3/4 in stock most totes are made from, both rules give the same figure: 1/4 in.
The reason is a trade between two things. A deeper cut gives the part more to bear on and more glue surface. It also leaves less wood under the floor of the cut, and the board is weakest along that line. One-third keeps two-thirds of the wall intact behind the joint. The figure is a convention that works in practice, not a calculation for your board, and it is not a load rating.
The cut list calculator applies this convention to your stock thickness and prints each housing and rabbet with its depth. If you plane your stock thinner, as Imani (fictional) may with her 13/16 in cherry, the depths change with it: a third of 13/16 in is a little over 1/4 in, so 1/4 in still serves.
The same source adds one more rule, for rabbets: the grain of the two parts should run the same way, unless one of them is plywood (Fine Woodworking). Wood moves across its grain as the air gets damper or drier and hardly moves along it. Two parts glued with their grain crossed are pulling against each other along the glue line every season. The rabbeted corner covers what that means for an end whose grain runs up and down.
One-third is a woodworking convention, not engineering. We do not rate the tote, its divider or its corners for any weight, and nothing here says a joint is strong enough for a given load. What you can check is the fit: the part goes in by hand, sits square, and the walls of the joint are clean. If a piece has to carry something heavy or valuable, the question of whether it will is one for a furniture maker who can see it.
3. Laying out from the part itself
A housing is only as good as the match between its width and the thickness of the part that goes in it. You can measure the divider with a rule, write down 23/32 in, and mark that on the wall, but every number you read and transfer is a chance to be off by the width of a pencil line. Robert Lang's advice in Popular Woodworking is to mark one piece directly from another wherever you can, and to use a knife or a fine pencil because a thick line can be wider than the tolerance you are working to (Popular Woodworking, Measure, Mark and Lay Out). That is the method here: the divider lays out its own housing.
Before you start, the reference marks from Marking out should be on every part: the face mark on the inside face of each wall, the edge mark on the bottom edge. Every line in this chapter is knifed or gauged from one of those surfaces, so the walls agree when the box goes together.
Locating the housing
Where the housing goes comes from the story stick, not from a tape. A story stick is a strip of wood marked with the real sizes of the project at full size, as Measuring without numbers describes. Lay the stick along the inside face of the wall and tick off the first compartment's size from the inside of the corner. On the rabbet path the inside of the corner is not the edge of the board. For a divider in the sides, tick from where the rabbet's shoulder will be; for a divider in the ends, tick from 1/4 in in from the end's edge, where the side's rabbet floor will sit. That tick is one wall of the housing.
Knifing the walls
- Knife the first wall. Put the square's stock against the reference edge and knife a line across the inside face at the tick.
- Stand the divider on that line. Set it on edge across the wall, its face tight to the knife line, on the waste side. Hold it square, or clamp a square against it.
- Knife the second wall along the divider's other face. Draw the knife lightly the first time, so it follows the divider rather than wandering. This line is the housing's width, taken from the part itself.
- Carry both lines down the edges. With the square on the face, knife each line down both edges to the depth you are about to gauge.
- Gauge the depth. Set a marking gauge to one-third of the thickness and run it along both edges, from the inside face, between the two knifed lines.
A marking gauge is a fence with a pin or wheel set at a fixed distance from it. Its job, in Dean Jansa's words for Popular Woodworking, is to carry a measurement from one board to another without numbers, and parts are gauged from the face side so they sit flush when assembled. His advice on technique: make the first pass with the pin barely touching, letting the pin trail rather than stand upright (Popular Woodworking, Mystery of the Marking Gauge).
Mark the waste between the knifed lines with a scribble or an X. When two lines sit 3/4 in apart, it is easy to saw on the wrong side of one of them, and a scribble costs a second.
Whether the divider is housed in the sides or the ends, the layout is the same: tick from the story stick, knife from the part, gauge from the inside face. Mark both walls of a pair at once by laying them side by side, inside faces up and the same edges together, and knifing across both. Two housings marked in one pass sit in the same place on both walls, which is what makes the divider stand square. For a stopped housing, also mark the stop: stand the divider in place on its bottom edge and tick its top edge on the wall, then square a short line across between the two walls.
4. Sawing, chopping and paring a housing
The housing is cut in three moves: the saw cuts the walls, the chisel removes the bulk of the waste, and the chisel pares the floor flat to the gauge line. Each tool does the part it does best.
Knifewalls: giving the saw a start
A knife line alone is a hairline, and a saw set on it can skate either way. Paul Sellers' answer is the knifewall: knife the line deep, then chisel a shallow sloping cut into it from the waste side, so the line becomes a little vertical wall with a trough beside it (Paul Sellers, Knifewalls). He uses it for the shoulders of tenons and dovetails and for the sides of housings. The saw sits in the trough, pressed against the wall, and starts in the right place without a struggle. The same wall, he notes, gives a square shoulder straight off the saw or ready for paring.
Sawing the walls
- Hold the work on the bench hook. Housings are crosscuts, so the ryoba's crosscut edge does them, or a crosscut backsaw. Sawing to a line covers the stance and the start.
- Saw on the waste side of each knifewall. The kerf, the slot the saw leaves, belongs in the waste, so the knifed line stays on the finished wall.
- Saw to the gauge line on both edges. Watch the near edge, then turn the board and check the far edge. Stop when the saw just reaches the gauge line on both. A housing sawn too deep on one edge shows as a gap that no paring removes.
- For a wide housing, add a cut or two in the waste. Extra kerfs between the walls, sawn to the same depth, break the waste into strips that come out more easily. In a 3/4 in housing one middle kerf is plenty.
Chopping and paring the waste
Two chisel actions do the rest. Chopping is driving the chisel with a mallet. Paring is pushing it by hand to take a thin, controlled slice. Popular Woodworking's guide to chisels notes that a bevel-edge chisel is not designed for heavy chopping, so take modest bites with it, and that you should define the layout lines with the edge before removing the waste (Popular Woodworking, Your Basic Guide to Chisels).
- Chop in from one edge. Hold a chisel narrower than the housing bevel up, its edge just above the gauge line, angled slightly upward. Tap it in toward the middle of the board and lever the waste out.
- Turn the board and repeat from the other edge. Working from both edges toward the middle keeps the chisel from breaking out the far edge, where the fibers have nothing behind them.
- Take the hump down. A ridge is left in the middle. Pare it down with hand pressure in thin slices, bevel up.
- Pare the floor to the gauge line. Lower the chisel until its back rests on the floor and you can feel the edge drop into the gauge line at each edge. Pare from each edge toward the middle until the floor is flat and the gauge lines are just split.
- Check the floor. Lay the chisel's back or a short straightedge across the floor along its length: no rocking, no light under it. Check that both walls are square to the face.
Pine crushes before it cuts if the chisel is dull. If the floor tears or the walls bruise, the edge needs Sharpening; When it goes wrong lists the signs.
For the work-holding, the bench hook takes the sawing. For chopping, clamp the wall flat to the table over a scrap so the chisel does not reach the tabletop. Chopping a housing's waste is lighter work than chopping a mortise, and much of it can be pared with hand pressure, which is near silent; A shop on a table covers protecting a veneered top and the noise of mallet work.
The router plane. A router plane holds a narrow blade at a fixed depth below a flat sole that rides on the face of the board. Set once, it brings the whole floor to the same depth, and it is quicker than paring to a gauge line when you have several housings to make. It is optional: the chisel and the gauge line do the same job. If you buy one later, set it to the gauged depth and take a few light passes after the chisel has removed most of the waste.
A stopped housing in a shelf. In furniture, a stopped housing usually hides the joint at the front of a shelf. Fine Woodworking stops it short of the front edge by the thickness of the material, and the shelf is notched to match (Fine Woodworking). Paul Sellers' free Common Woodworking series includes a stopped housing project among its beginner courses (Common Woodworking, All Courses).
The stopped housing on the tote
The tote's divider is shorter than the ends are tall, so its housing stops at the divider's top edge. The bottom of the housing is open at the end's bottom edge, which the tote's bottom covers. The saw cannot run the full length of a stopped housing, because its teeth would cut past the stop, so the stopped end is cut first with the chisel.
- Chop a pocket at the stop. Between the two knifed walls, just inside the stop line, chop straight down to the gauged depth over about an inch, levering the waste out toward the open end. The flat face of the chisel goes on the stop line for the last chop, so the stop is a clean square wall.
- Saw the walls from the open end. Start each wall at the bottom edge and saw toward the stop with the saw tilted, so its far teeth run into the pocket. Lower the saw as you go until the cut reaches the gauge line at the open edge and the floor of the pocket at the stop.
- Chop and pare the rest. Remove the waste between the walls as for a through housing, working from the open end toward the pocket, and pare the floor flat to the gauge line and to the pocket's floor.
In an end whose grain runs up and down, the walls of this slot run with the grain, so they are rip cuts, and the waste comes away in long splits. A split follows the grain, not your line, and it can dive below the gauge line. Take the waste down in thin layers, and pare in the direction where the fibers rise toward the surface, as Choosing wood explains for reading grain. On the inside face of Noor's ends this groove and the handle's mortise sit on one line, both centered on the divider; Test it look along that line for a split after chopping the mortise, since both cuts run with the same fibers.
5. The rabbeted corner
A rabbet across the end of a board is cut the same way as half a housing. In fact it is close to a one-sided tenon: one crosscut makes the shoulder, one cut along the grain from the end makes the floor.
Laying out a corner rabbet
- Take the width from the end itself. The rabbet is as wide as the end of the tote is thick. Lay the end piece flat on the inside face of the side, flush with the side's squared end, and knife along its inner face. That line is the shoulder.
- Carry the shoulder line down both edges. Knife it square to the face, down to the depth.
- Gauge the depth. From the inside face, gauge one-third of the thickness (1/4 in in 3/4 in stock) across the end grain and along both edges to the shoulder line.
- Mark the waste. The waste is the block between the shoulder, the end of the board and the gauge line.
Cutting it
- Saw the shoulder. Make a knifewall, then crosscut on the waste side to the gauge line on both edges, on the bench hook. This is the cut that shows on the inside of the box.
- Remove the waste. Either saw down the gauge line from the end grain to the shoulder with the rip edge, holding the board upright in a clamp, or split and pare the waste away from the end with the chisel bevel up, a layer at a time, working down to the gauge line. Sawing is quicker and more certain on a straight-grained board; paring gives more control on a board with wild grain.
- Pare the floor flat and the shoulder clean. The end of the tote has to seat on the floor and against the shoulder along its whole height. Check both with a square.
When the end's grain runs up and down
On Noor's tote, the side's grain runs along its length, and the end's grain runs up and down. Where they meet, the edge of the end sits on the floor of the rabbet, and the two grains cross at a right angle. Convention Fine Woodworking's convention is that both parts of a rabbet joint have their grain running the same way, except in plywood. Noor's corner departs from it. Hal's (fictional) and Imani's ends, with their grain running across, follow it, because their dovetailed corners require it anyway.
What her joint does differently is a matter of movement. Physical principle Across the 4 1/4 in height of the side, the side moves with the seasons and the end, which runs along its grain in that direction, hardly moves. The movement calculator puts the change in a 4 1/4 in side of unknown species, indoors in most of the US, at about 1/16 in (0.064 in) between the driest and dampest months, using the largest coefficient it lists; in eastern white pine it is about 1/32 in. The figures come from the Forest Service's Wood Handbook, chapter 4 (Wood Handbook, Moisture Relations), and they are averages with real variation. The ends move too: each 7 1/4 in end grows and shrinks across the tote's width by about 7/64 in on the same basis. The sides simply move out and in with it, and so does the bottom, whose grain runs the length of the tote so that it moves across its width in step.
Her corner is glued and nailed. The glue line sits where the side moves and the end does not; the nails pin the end in its rabbet and flex a little, so the crossed-grain corner can move with the seasons. Test it Look at the corners after a change of season: a hairline at the top of the rabbet's shoulder shows the side moving against the end. Choosing wood works out the same figure for her sides. To follow the convention instead, cut the ends from a board as wide as the end is tall, with the grain running across the end, as Hal and Imani do.
The movement figures are estimates from published averages. Your board may move more or less, and the calculator does not know its species unless you do. How a crossed-grain glue line behaves on your tote over the seasons is something time shows, not this chapter. Nothing here rates the corner for a load.
Assembly, in brief
Dry-fit all four walls and the divider before any glue. The ends drop into the rabbets, the divider drops into its housings, and the whole box should stand square on a flat surface with its diagonals equal. Glue goes on the rabbet floors and shoulders and in the housings; the nails go through the side's remaining 1/2 in lip into the edge of the end. Gluing up, clamping and nailing are covered in Glue, finish and mending, including the glue's working time.
Nails in a rabbeted corner. On Noor's tote the nails pass through the side's 1/2 in lip and into the edge of the end. Because the end's grain runs up and down, its edge is long grain, and the nails enter it across the fibers rather than between them as they would in end grain. We found no free source that gives holding figures for small nails in a box this size, so we give none. Two practical points instead, both ours rather than a source's. Test it Drive one nail into an offcut first: if the lip or the end's edge splits, drill a pilot hole a little smaller than the nail. Angle neighboring nails slightly toward and away from each other, so the corner cannot pull straight off them. Pins (thin brads) split less and hold less.
Fitting by paring
A good fit, for both joints, is a part that goes in with hand pressure: snug enough to hold its own weight, not so tight that it needs a mallet. A part that has to be driven in is trying to split the wall it is going into, and a housing near the end of a board has little wood to resist.
When a part is tight, take wood off the part, not the joint. The housing's walls are knifed lines that also set where the divider sits; pare one, and the divider moves or leans. The divider's face, by contrast, can lose a fine shaving to a plane or a paring chisel and nothing else changes. Try the fit, look for shiny burnished patches on the part where it rubbed, and take a shaving there. Repeat until it slides in. The Planing a board square chapter covers setting the plane for a fine shaving.
When a part is loose, paring cannot help. A slightly loose housing still locates the divider and glue fills a little; a sloppy one is better cut again a little further along, or in a fresh piece. When it goes wrong covers gaps.
Test it Check the divider for square in two directions: square to the face of the wall it sits in, and its top edge level with the wall's top edge. A divider that leans means one wall of the housing wandered off its line or the floor is deeper at one edge than the other.
6. See it See it
Noor's corner rabbets and divider groove. Noor (fictional) is building a cleaning tote for the cabinet under her kitchen sink, from two 6 ft big-box 1x6 boards (3/4 by 5 1/2 in actual, species unknown) and a 2 ft 1x8 (3/4 by 7 1/4 in) for the ends. Her divider runs the length of the tote. It makes compartment A, 2 3/4 in wide, for two spray bottles and a scrub brush, and compartment B, 3 1/4 in wide, for a box of cloths standing on edge. The handle runs over the divider, so the 10 1/4 in bottles stand beside it.
Her parts, from the cut list. Sides 10 3/4 in long by 4 1/4 in high, grain along the length. Ends 10 1/2 in tall by 7 1/4 in wide, the full width of the 1x8, grain up and down. Divider 9 3/4 in long by 4 1/4 in high.
The rabbets. At each end of each side, on the inside face: 3/4 in wide, taken by laying the end piece itself on the side and knifing along it, and 1/4 in deep, gauged from the inside face. That leaves a 1/2 in lip to nail through. Each end is 7 1/4 in wide because it sits 1/4 in into a rabbet on each side of the 6 3/4 in inside width.
The divider slot. Because her ends' grain runs up and down, the slot for the divider runs with the grain: strictly a groove, 3/4 in wide and 1/4 in deep. She lays the two ends side by side, inside faces up and bottom edges together, ticks compartment A's 2 3/4 in from the story stick (starting 1/4 in in from the edge, where the side's rabbet floor will sit), knifes the first wall, stands the divider on the line and knifes its other face. She ticks the divider's 4 1/4 in height for the stop, chops the pocket, saws both walls up from the bottom edge, and pares the waste in thin layers, watching the grain. She chops before 8 p.m. and pares after.
Known: the board's actual thickness (3/4 in, measured), the compartment widths from the contents on her story stick, the depths from the one-third convention. Assumed: that the boards have settled after a week lying flat in her kitchen. Noor has no moisture meter, so this is her assumption; Choosing wood covers the check she made instead. Open: how her crossed-grain corners, glued and nailed against Fine Woodworking's matching-grain convention, behave over the seasons; she looks at them after a change of season. Also open: whether the downstairs neighbor minds mallet work in the evening; asking settles it.
The fit. The scrap divider was tight on the first try. She found two shiny patches on its faces, took one plane shaving off one face, and it slid in with hand pressure and stood square.
A true housing: Hal (fictional). Hal's garden tote has dovetailed corners, so his ends, 10 3/4 in wide by 9 1/4 in tall, are yellow-poplar with the grain running across. His lengthwise divider's slot runs up and down each end, across that grain, so his is a true housing: stopped at the divider's top, its walls crosscuts, and its waste chopped across the fibers rather than split along them. He chops it with his father's wooden mallet, and only once his chipped chisels have been through Sharpening.
Free sources that show these joints:
- Fine Woodworking, All About Rabbet and Dado Joints: the depth conventions, the grain rule for rabbets and the stopped housing, in one article.
- Paul Sellers, Knifewalls: his blog post on the knife line turned into a wall that guides the saw.
- Common Woodworking, All Courses: Paul Sellers' free beginner series, which includes a housing dado and a stopped housing project, each in illustrated steps.
- Popular Woodworking, Measure, Mark and Lay Out: Robert Lang on marking one part from another rather than from numbers.
7. Practice Practice
Minimum: one housing in a scrap, fitted with a scrap divider that goes in by hand pressure and stands square. Time: about an hour for the housing; another 45 minutes for the rabbet. Materials: two offcuts of your tote stock about 10 in long, a third offcut to stand in for the divider, your knife, square, marking gauge, saw, a 1/2 in chisel, a mallet, the bench hook, and a pencil.
- Mark reference faces on the offcuts. Face mark on what will be the inside face, edge mark on the bottom edge, as in Marking out.
- Lay out the housing from the scrap divider. Knife one wall about 4 in from the end, stand the divider against it, knife the second wall, carry both down the edges and gauge 1/4 in deep from the face.
- Make the knifewalls, saw, chop and pare. Saw to the gauge line on both edges, chop from both edges, pare the floor flat.
- Fit the divider. If tight, take a shaving off its face and try again. Stop when it goes in by hand and stands square. Write the number of tries and what you changed in the practice log.
- Cut a corner rabbet on the second offcut. Lay a piece of your end stock on it, knife the shoulder, gauge 1/4 in, saw the shoulder and remove the waste. Seat the end piece in it and check that it sits flat on the floor and tight to the shoulder.
- Then the tote. When the practice pieces fit, cut the tote's own housings and rabbets and tick them off on the tote project sheet.
A second housing, against the clock of your own eye. Cut another housing in the same offcut, this time without the scrap divider: measure it with a rule and mark the width as a number. Fit the same divider. Most people find the knifed-from-the-part housing fits on the first or second try and the measured one takes longer. Note which in the practice log.
8. Your setup Your setup
9. Check your work Check your work
Criteria
- Does the part go in with hand pressure, without a mallet, and stay in when you lift the board?
- Does the divider stand square to the face of the wall, and level with its top edge?
- Is the floor flat, with the gauge line just split on both edges?
- Are both walls of the housing clean knifed lines, with no saw marks on the finished side?
- Does the end of the tote seat on the rabbet's floor and against its shoulder along its whole height, with no light showing?
- Are both housings in a pair at the same distance from the corner, so the divider stands square across the box?
Worked example
Noor's practice housing: the divider went in by hand on the second try, after one shaving. It stood square to the face, and its top edge sat level with the wall within the thickness of a knife line. The floor was flat under the chisel's back. One wall showed a short scratch where the saw had started a hair outside the knifewall; that would show in the finished box, so on the tote she checked each knifewall before sawing. Her corner rabbet seated flat but showed a thin gap at the top of the shoulder, because she had sawn the shoulder slightly past square. She pared the shoulder until the gap closed and checked it with the square. On the tote, both divider slots were marked across both ends at once, and the divider stood square across the box on the dry fit.
Common mistakes
- Sawing on the wrong side of a line. The housing comes out a kerf too wide. Mark the waste before you saw.
- Sawing deeper on one edge than the other. Paring the floor flat would then take it below the gauge line on the shallow edge. Check the far edge before you stop.
- Chopping straight through from one edge. The far edge breaks out. Work in from both edges.
- Driving a tight part home. The wall splits along its grain. Pare the part instead.
- Paring the housing's wall to ease a fit. The divider shifts and may lean. Pare the divider.
- Measuring the rabbet's width with a rule. It comes out a hair wide or narrow and the end rocks in it. Knife it from the end piece itself.
What is still unresolved
This chapter does not settle how well the joints hold in use; a snug fit is what it checks. The glue, the clamping and the nails are in Glue, finish and mending. The handle's joint is in Mortise and tenon, and the standard corner is in Dovetails. How a crossed-grain rabbet behaves over the seasons is something time shows. Whether a piece will carry a given weight is a question for a furniture maker who can see it.