Mortise and tenon
Joints and assembly

Mortise and tenon: a handle tenoned through the ends

Size a tenon from the stock by the one-third convention, chop a through mortise from both faces, saw and pare the tenon to fit, and join the tote's handle to its ends, glued, wedged or pinned.

Start here Essentials

At minimum this chapter asks you to chop one through mortise in a scrap and fit one tenon to it. Chopping is the loudest work in this manual, so plan when and where you do it. Everything marked Go deeper is optional on a first pass.

  1. Choose a chisel near one-third of the end's thickness and set the gauge to it. In 3/4 in stock that is the 1/4 in chisel (Sizing the tenon).
  2. Lay out the mortise on both faces of a scrap. Gauge from one reference edge and square from one end, so the two outlines line up (Laying out).
  3. Chop halfway from each face. Clamp the scrap over a table leg, with a board under it (Chopping a through mortise).
  4. Saw and pare a tenon on a second scrap to fit. Saw the cheeks and shoulders, then pare the cheeks until it goes in (Sawing and fitting the tenon).

Minimum time: about two hours for the first joint. Done when: the practice tenon passes through the mortise with hand pressure, shoulders tight on both faces.

1. The joint and its parts Understand

A mortise is a rectangular hole cut into one part. A tenon is a tongue on the end of another part, sized to fill the mortise. The tenon's broad faces are its cheeks; the steps where the tenon meets the full width of its part are its shoulders. A through mortise goes all the way through its part, so the end of the tenon shows on the far face; a blind mortise stops inside.

The shoulders are what make the joint more than a peg in a hole. When the tenoned part is pushed sideways, the shoulders bear on the face of the mortised part and resist the bending and twisting. Garrett Hack makes this point in Fine Woodworking about tables, where an apron tenons into a leg, and adds that thicker parts give stronger shoulders (Fine Woodworking, Joining Legs to Aprons). The word for a frame pushed out of square is racking, and shoulders that sit tight all round are what resist it.

On the tote, the handle runs the length of the box, over the divider, and its tenons pass through the two ends. A carried tote pulls the handle up and swings it, so both jobs matter: the tenon holds the handle in the ends, and its shoulders keep the ends from leaning in or out. The handle also ties the tops of the two ends together. The tote's other joints are in Housings and rabbets and Dovetails; Which joint where compares them all.

A through tenon on the tote is cut flush with the outside of the end. Its length is not a choice: it is the thickness of the end it passes through, 3/4 in in 3/4 in stock.

2. Sizing the tenon

Three sizes define a tenon: its thickness (the distance between its cheeks), its width (the distance between its edge shoulders) and its length. The handbooks give rules of thumb for each. They are conventions from hand joinery, not engineering.

SizeConventionSourceOn Noor's handle
ThicknessOne-third of the thickness of the stock being mortisedPopular Woodworking, Tenons Rule1/4 in, a third of the 3/4 in end
WidthHalf the width of the tenoned part; split into two tenons if the width would pass six times the thicknessPopular Woodworking, after Ellis5/8 in, half the handle's 1 1/4 in height, leaving 5/16 in shoulders above and below
LengthAt least five times the thickness for a blind tenon; a through tenon is as long as the part it passes throughPopular Woodworking3/4 in, the end's thickness, cut flush

Convention The one-third rule for thickness is the traditional one. Popular Woodworking's article traces it through the old joinery texts: a 3/4 in part takes a 1/4 in tenon, and it notes that some modern books say one-half, which the author ties to machine mortising. For mortises chopped by hand it calls one-third the better fit (Popular Woodworking). The reason is the wood left either side of the mortise: one-third leaves two walls each a third of the stock thick, and the mortise walls are what a chisel levers against while chopping.

In practice the tenon's thickness is set by the chisel you own. A mortise is chopped with a chisel the same width as the mortise, so you pick the chisel nearest one-third of the stock and make the tenon to match it. In 3/4 in stock that is the 1/4 in chisel from the kit in The first tools.

Noor's handle falls short of one rule, and it is worth saying so. Five times a 1/4 in tenon is 1 1/4 in, and her tenon is 3/4 in long, because a through tenon is only as long as the end is thick. The five-times rule is written for blind tenons in frames, such as table aprons. The tote's handle tenon is shorter, glued through the full thickness of the end, and it can be wedged. Whether it is enough for what she carries is something a test answers, not the rule.

Limits

The handle's strength depends on the wood, the grain, the fit and the glue, and nothing in this chapter rates it for a weight. What you can check is visible: shoulders tight on both faces of each end, no gap at the cheeks, and no split running from the mortise. Test it Load the finished tote with what it will carry and lift it by the handle a few inches above a soft surface before you rely on it. If the tote is for anything heavy or valuable, show it to a furniture maker.

Go deeper

Where the sources differ on thickness. Popular Woodworking's article gives one-third and ties one-half to machine work. Garrett Hack's rule of thumb in Fine Woodworking is "a little more than one-third" of the apron, and in a soft wood such as butternut, with 3/4 in aprons, he makes the tenon at least 5/16 in, maybe 3/8 in (Fine Woodworking). Both are about frames where a thin apron meets a thick leg. On the tote, the tenoned part (the handle) and the mortised part (the end) are both 3/4 in, so a thicker tenon takes wood from the end's mortise walls. We keep one-third, 1/4 in, because it matches a kit chisel and leaves the end's walls as thick as the tenon. A reader working in a soft, crushable pine who owns a 5/16 in chisel has a reasonable case for it, on Hack's reasoning.

The haunched tenon. Where a tenon sits at the very end of a part, as when a rail meets the top of a leg, the mortise would run out of the end. A haunched tenon cuts the tenon narrower and leaves a short stub, the haunch, at full thickness near the end, which fills the top of the mortise without opening it. Paul Sellers' free Common Woodworking series has a haunched mortise and tenon among its beginner projects (Common Woodworking, All Courses). The tote's handle sits well below the tops of the ends, so it does not need one.

3. Laying out from the handle and the end

A through mortise is chopped from both faces, so it is laid out on both faces, and the two outlines have to line up. That is the whole art of the layout: every line on both faces is gauged from the same reference edge or squared from the same end. Robert Lang's advice in Popular Woodworking applies here as everywhere: mark one part from another rather than from numbers wherever you can (Popular Woodworking, Measure, Mark and Lay Out). The reference marks from Marking out tell you which edge and face to work from.

Set the gauge to the chisel

Hold the 1/4 in chisel's edge against the marking gauge's pin and set the fence so the pin lands on the far corner of the chisel. On the handle, run the gauge from one face, then from the other face. In 3/4 in stock the two lines fall 1/4 in apart, centered, because 3/4 in is three times 1/4 in. Lay the chisel's edge between them to check: it should just cover the gap. Run both lines across the end grain of the handle and down both edges to the shoulder line. Dean Jansa's note for Popular Woodworking on the gauge applies: a light first pass, with the pin trailing (Popular Woodworking, Mystery of the Marking Gauge).

The shoulder lines, from the sides

The distance between the handle's two shoulders is the tote's inside length. Take it from the parts, not from a rule. On the rabbet path, lay the handle along one of the sides and knife across it at the two rabbet shoulders; on the dovetail path, take it from the baselines on a side, or from the story stick. Square those two marks round all four faces of the handle with the knife. Then gauge the edge shoulders, 5/16 in down from the top edge and up from the bottom edge on Noor's handle, across the end grain and along both cheeks to the shoulder line.

The mortise, on both faces of the end

  1. Find the height. Hold the handle against the end at its finished height, its top 3/4 in below the end's top on Noor's tote, and tick the top and bottom of the tenon (the edge shoulder lines) onto the end's edge. Square both ticks across the inside face and the outside face, from the same end of the board.
  2. Find the position across the end. The handle is centered over the divider, so the mortise is centered on the divider's slot. Square the slot's walls up the inside face to the mortise height; the mortise sits midway between them.
  3. Gauge the walls on both faces. Set the gauge from the end's reference edge to the first mortise wall and run it on both faces; reset to the second wall, check the chisel fits between, and run it on both faces. Because both faces are gauged from the same edge, the outlines line up even if the board is not quite the width the cut list says.
  4. Mark the waste. Scribble inside both outlines.

Preference If you can, chop the mortise while the end is still at its rough length, about an inch long, as Glen Huey suggests for rough parts in Popular Woodworking (Popular Woodworking, Why Wood Warps). Lay out from the finished top line, chop, then saw the end to length. On Noor's ends, whose grain runs up and down, the mortise's top sits 1 1/16 in below the finished top, along the grain, and the extra inch gives the chisel more wood to wedge against while it works. That order is our suggestion, not a source's rule.

Go deeper

The mortise gauge. A mortise gauge has two pins, one fixed and one adjustable, so both walls of a mortise or both cheeks of a tenon are marked in one pass at one setting. Set the pins to the chisel's width, then set the fence for the position. It saves the resetting above and keeps the mortise and tenon matched. It is a later purchase: a single-pin gauge does the same work in two passes.

4. Chopping a through mortise

Caution

Clamp the work; do not hold it in one hand while you strike with the other. Keep both hands behind the cutting edge, and keep the free hand off the far side of the work, where the chisel comes out. For a cut that will not stop bleeding, call 911 or your local emergency number; the American Red Cross first aid page on wounds says what to do and when a cut needs emergency care. Follow it, not us.

Where and when to chop

A mallet on a chisel is the loudest thing you will do in this manual. The only hand-tool figure we found on an agency noise chart is hammering, at 94 to 97 dBA, on a chart that says extended exposure at or above 85 dBA can damage hearing (WSCC, How Loud Is It?). Mallet work is not measured there, and it comes in short bursts, but it carries through a floor. Your lease or building rules say which hours are quiet; your neighbors say whether they mind.

The blow goes down through the work and into whatever holds it up. Clamp the end flat on the table directly over a table leg, so the force goes into the leg and the floor rather than bouncing the middle of the top. Put a flat scrap board between the work and the table, which protects a veneered top and gives the chisel something to meet when it breaks through. A shop on a table covers holding work over a leg, protecting the top, and quiet hours. A sturdy block on the floor is an alternative where a table is too light.

The chisel and the chopping

The kit's chisels are bevel-edge. Popular Woodworking's guide to chisels notes that bevel-edge chisels are not designed for heavy chopping, and that a mortise chisel, with a thick blade, is built to be driven with a mallet and used to lever waste out (Popular Woodworking, Your Basic Guide to Chisels). A 1/4 in bevel-edge chisel chops a small mortise in pine or poplar if you take small bites, strike moderately and lever gently. The same guide's advice on keeping the chisel at 90 degrees: sight its profile, from the side and from the front.

  1. Mark half the depth on the chisel. A strip of tape on the back of the blade at half the stock's thickness, 3/8 in in 3/4 in stock, shows when to stop.
  2. Start in the middle, away from the end lines. Stand the chisel upright, bevel facing the nearer end of the mortise, its edge between the two gauge lines and square to them. Strike once, moderately.
  3. Step toward one end. Move the chisel about 1/8 in toward the end line and strike again. Each cut chops a small wedge free. Stop about 1/16 in short of the end line.
  4. Turn and work toward the other end. Reverse the chisel, bevel facing the other end, and repeat from the middle out, again stopping short of the line.
  5. Lever out the waste. Lever the chips toward the middle, against the waste, not against the end walls. Repeat the passes until the tape reaches the surface.
  6. Chop the end walls. With the flat face of the chisel on the end line and the bevel facing into the mortise, chop straight down to depth at each end. These are the last cuts, so the levering above does not crush them.
  7. Turn the work over and repeat from the other face. The two halves meet in the middle. Pare away any step where they meet, holding the chisel's back against the walls, until the chisel slides through freely.

Chopping from both faces is what keeps a through mortise clean. A chisel driven right through from one face breaks out fibers on the far face as it emerges, exactly where the joint shows. Starting from each face means each face's edges are cut from the outside, by the chisel's edge, rather than burst from inside.

Check the walls as you go. Sight down the mortise against a square stood on the face: the long walls should be square to the face and straight. A wall that leans on one face and the other leaves a waist or a twist that the tenon will not pass.

Test it Watch for splits. A chisel struck across the grain wedges the fibers apart, and in an end whose grain runs up and down that wedge points toward the top of the board. If a crack starts from the mortise, stop and look; When it goes wrong lists what it means and what to do.

5. Sawing and fitting the tenon

A tenon is four saw cuts and some paring. The cheeks are rip cuts, along the grain from the end of the part to the shoulder; the shoulders are crosscuts. Sawing to a line covers both, and the knifewall that starts a crosscut in the right place.

  1. Saw the cheeks. Clamp the handle upright, or at an angle, at the table's edge. With the rip edge of the ryoba, saw on the waste side of each cheek line, down to the shoulder line, watching both edges. Leave the gauge line on the tenon: you pare down to it, and you cannot put wood back.
  2. Saw the edge cheeks. The 5/16 in strips above and below the tenon come off the same way, sawn from the end to the shoulder line.
  3. Saw the shoulders. Lay the handle on the bench hook, make a knifewall on the waste side of the shoulder line, and crosscut down to the cheek. Stop when the saw reaches the cheek; a shoulder cut too deep weakens the tenon at its root.
  4. Clean the shoulders. Pare any ragged fibers from the shoulders with the chisel's back on the knifed line. The shoulders are what show and what bear, so they must be square across the handle and in one plane on both faces.
  5. Try the fit and pare the cheeks. Present the tenon to the mortise. If it will not start, pare the cheeks, a few fibers at a time, keeping them flat and parallel. Push it in by hand, pull it out and look for shiny, burnished patches: those are where it binds. Pare there.

The fit you want is the same as for a housing: in with hand pressure, firm enough that the end stays on the tenon when you lift the handle, and not driven with a mallet. A tight tenon driven home splits the end along its grain. A loose one has a gap at a cheek, and glue does not fill gaps well; When it goes wrong covers what to do.

When the tenon is in, look at both faces of the end. The shoulders on the inside face should close all round, with no light. The tenon's end on the outside face should fill the mortise with no gap at its edges. Pare the tenon's end flush with the outside of the end after the glue has set, using the chisel's back flat on the face, or a block plane.

6. Glued, wedged or drawbored

A tenon that fits holds in place by friction until it is secured. The tote's default is glue alone. Two older ways of locking a mortise and tenon are wedging and drawboring; both are optional, and this section compares them.

MethodHow it holdsOn the toteSource
GluedGlue on the cheeks and mortise wallsThe default. Noor glues hersTitebond Original specifications
Kerf-wedgedWedges driven into saw kerfs spread the tenon into a flared mortise, a dovetail shapeWorks on a through tenon. Imani wedges hersPopular Woodworking, Caspar; Woodcraft, Burton
DrawboredA wooden pin through offset holes pulls the shoulders tightAwkward: the pin would enter through the end's edge, which the side coversPopular Woodworking, Rawls
Tusk (keyed)A wedge through the tenon's extended end, outside the mortiseNeeds a tenon that sticks out; the tote's are flushPopular Woodworking, Follansbee

Glued

Glue goes on both cheeks of the tenon and the long walls of the mortise. Product-specific Titebond Original's maker gives 4 to 6 minutes of open assembly time at 70 F and 50 percent humidity, and says the glue, the air and the wood should all be at 50 F or warmer (Titebond Original). That rules out Hal's (fictional) garage in March, at about 45 F, unless he glues indoors. The maker's FAQ says not to stress a new joint for at least 24 hours (Titebond FAQ). On the tote, the handle goes in at the same glue-up as the ends and the rest of the box; Glue, finish and mending covers the sequence and the clamping.

Go deeper

Kerf-wedged, with a flared mortise

Tom Caspar's article for Popular Woodworking explains the mechanics. Two saw kerfs are cut into the end of the tenon, one near each edge. The ends of the mortise are pared into a slight flare on the outside face. When wedges are driven into the kerfs, the tenon spreads into a fan or dovetail shape that fills the flare, and, in his words, "Like a dovetail, this joint can't pull apart after the wedges go home." He tapers the mortise ends at 3 degrees over about three-quarters of the mortise's depth, leaving the rest square, and notes the taper can go up to 8 degrees. His wedges have the same angle as the taper, are about 1 in longer than the tenon, and are tested dry before glue goes on the kerfs and the flared spaces. His method uses machines; the figures and the principle carry over to hand work (Popular Woodworking, Wedged Mortise and Tenon).

Physical principle Which way the kerfs run is the part that matters most. Ken Burton, answering a reader for Woodcraft, traced a split seat to a wedge slot that ran parallel to the seat's grain; his rule is that wedge slots in through tenons run perpendicular to the grain of the mortised part (Woodcraft, Avoiding Splits with Wedged Tenons). That way the wedge pushes the tenon against the mortise's end-grain walls, which bear the pressure, and not against its long-grain walls, which split. Christopher Schwarz, in Popular Woodworking, says the same: pushing a tenon against the long-grain walls of a mortise "is asking for trouble" (Popular Woodworking, Diagonal Wedges).

So the grain of the end decides the layout:

  • An end with grain running up and down (Noor's). The mortise's short walls, at its top and bottom, are the end-grain walls. The kerfs run across the tenon, one near its top edge and one near its bottom edge, and the flare is pared on the mortise's top and bottom walls.
  • An end with grain running across (Hal's and Imani's dovetailed ends). The mortise's long walls are the end-grain walls. The kerf runs up and down the tenon, and the flare is pared on the long walls. On a tenon only 1/4 in thick, that is one kerf down the middle, the single slot Burton describes.

Burton's other figures: a tenon cut 1/8 to 1/4 in longer than the part is thick, trimmed flush after; a wedge about twice as thick as the slot is wide; a small hole drilled where the slot ends, usually 1/8 to 1/4 in short of the shoulder, so the split stops there; a wooden mallet; and drive until moderate blows no longer move the wedge. Caspar's relief holes are larger, sized for oak, and would not fit a 5/8 in tenon. Cut the wedges from a hard, straight-grained offcut, and make a practice joint before the tote's.

Paul Sellers, on his blog, describes the same flaring of the mortise ends so the tenon can spread into the gap, and calls it the method he uses most (Paul Sellers, Wedged and Pegged Tenons).

Drawbored

A drawbore pulls the joint together without clamps. A hole is bored through the mortise's cheeks; the tenon is inserted and the hole's center is marked on it; the tenon comes out and is bored a little closer to its shoulder than the mark; then a tapered wooden pin driven through the offset holes pulls the shoulders tight. Andy Rawls' rule in Popular Woodworking is that the most offset you need is 1/16 in, and more risks breaking the pin; he makes pins from straight-grained wood, preferably oak or hickory (Popular Woodworking, Drawbore with Andy Rawls). The pin crosses the tenon at right angles to its cheeks. On a table, where an apron's tenon enters a leg, that means boring through the leg's face. On the tote, the handle's cheeks face the sides of the box, so the pin would have to enter through the end's edge, which sits in the side's rabbet or dovetails. That is why we name drawboring for other frames rather than the tote.

Tusk tenons

Peter Follansbee's article in Popular Woodworking shows a different wedged joint: the tenon runs well past the mortised part, and a wedge through a hole in its protruding end draws the parts together. It can be taken apart by knocking the wedge out (Popular Woodworking, The Wedged Mortise and Tenon). It needs a tenon that sticks out, so it suits benches and trestles rather than a flush-sided tote.

7. See it See it

Fictional example

Noor's handle. Noor (fictional) is building a cleaning tote from big-box 1x6 and 1x8, 3/4 in thick, species unknown. Her handle is 10 3/4 in long, 1 1/4 in high and 3/4 in thick, and it runs over the divider, so her 10 1/4 in spray bottles stand beside it rather than under it. Its top sits 3/4 in below the tops of the ends.

The tenon. One-third of the 3/4 in end gives a 1/4 in tenon, and she owns a 1/4 in chisel. Half the handle's 1 1/4 in height gives a tenon 5/8 in high, with 5/16 in shoulders above and below. Through a 3/4 in end, the tenon is 3/4 in long and cut flush. She took the shoulder lines from one side: laid along it, the handle was knifed at the two rabbet shoulders, 9 1/4 in apart, the tote's inside length.

The mortise. In each end, 1/4 in wide by 5/8 in long, the long way running with the end's up-and-down grain. It is centered over the divider's slot: she squared the slot's walls up the inside face and gauged the mortise walls midway between them, from the same edge on both faces. Its top is 1 1/16 in below the finished top of the end. She chopped both mortises with the ends still an inch long at the top, over the leg nearest the window, with a scrap of 1x6 under them, between 6 and 7 p.m., and sawed the ends to length afterward.

The fit. The first tenon would not start. She pared the cheeks twice, looking for the shiny patches each time, and it went through with hand pressure. The second needed one paring. She glues both at the main glue-up.

Known: the stock thickness, the handle's sizes from the cut list, the chisel she owns. Assumed: that the board has settled after a week flat in her kitchen; she has no meter. Open: whether her downstairs neighbor minds mallet work after 8 p.m. She settles that by asking, and chops earlier until she has. Also open: whether the handle sits low enough once the bottom's thickness is added. Her story stick settles it: the tote stands 11 1/4 in with its bottom, under the cabinet's 11 1/2 in clear height, with 1/4 in to spare.

Imani (fictional) wedges hers. Imani's caddy is cherry with dovetailed corners, so her ends' grain runs across. She cuts one kerf down the middle of each tenon, up and down, across the end's grain, and pares the mortise's long walls into a slight flare on the outside face. She tests the wedges dry, glues them, and pares them flush the next day.

Free sources that show the joint:

8. Practice Practice

Minimum: one through mortise in a scrap and one tenon on a second scrap that passes through it with hand pressure, shoulders tight on both faces. Time: about two hours. Materials: two offcuts of your tote stock about 10 in long, one of them at least as wide as your handle is high; your knife, square, marking gauge, saw, the 1/4 in chisel, a 1/2 in chisel for paring, a mallet, a clamp, a flat scrap to chop on, tape and a pencil.

  1. Set the gauge to the chisel and mark the tenon. Gauge the cheeks from both faces of one offcut, square a shoulder line about 1 in from its end, and gauge the edge shoulders.
  2. Lay out the mortise on the other offcut. Both faces, from the same reference edge and the same end, about 2 in from the end of the offcut.
  3. Chop it from both faces. Over a table leg, at an hour that suits your building, with tape on the chisel at half depth.
  4. Saw the tenon and fit it. Leave the gauge lines, then pare to them, checking for shiny patches.
  5. Note it. Write the time, the number of fittings and anything that went wrong in the practice log. Then lay out the tote's handle and ends, and tick them off on the tote project sheet.
Go deeper

A wedged practice joint. Cut a second mortise and tenon with the tenon 1/8 in long. Pare a 3 degree flare on the two end-grain walls of the mortise, on one face only. Saw the kerfs across the mortised part's grain, drill a small relief hole at each kerf's end, cut two wedges from a hard offcut, test them dry, then glue and drive them. When the glue has set, saw the joint through the middle and look at how the tenon filled the flare.

9. Your setup Your setup

10. Check your work Check your work

Criteria

  • Does the tenon pass through the mortise with hand pressure, and stay in when you lift the tenoned part?
  • Do the shoulders close on the face with no light showing, on both cheeks and both edges?
  • Does the tenon's end fill the mortise on the far face, with no gap at its edges?
  • Are both faces of the mortised part clean around the mortise, with no broken-out fibers?
  • Is there any crack running from the mortise along the grain?
  • Does the tenoned part stand square to the mortised part, checked with a square in both directions?

Worked example

Noor's practice joint: the tenon passed through on the third try with hand pressure. The shoulders closed on three sides; the bottom edge shoulder showed a thin gap, because she had sawn it slightly past square. On the tote's handle she checked each shoulder line with the square before sawing. The far face of the mortise was clean, since she had chopped from both faces, but one long wall leaned, so the tenon was snug at one face and loose at the other. She pared the wall straight and noted in her practice log to sight the chisel's profile from the front as well as the side. No cracks. The handle stood square to the end on both checks.

Common mistakes

  • Laying out the two faces from different edges. The two halves of the mortise miss each other in the middle. Gauge both faces from one edge.
  • Chopping right through from one face. The far face breaks out. Chop halfway from each.
  • Levering against the end walls. The ends of the mortise crush and the shoulder shows a gap. Lever against the waste; cut the end walls last.
  • Sawing on the line instead of beside it. The tenon comes out thin. Saw on the waste side and pare to the line.
  • Driving a tight tenon home. The end splits along its grain. Pare the cheeks instead.
  • Kerfs running the wrong way, if wedging. The wedges push against long grain and split the end. Run the kerfs across the mortised part's grain.

What is still unresolved

This chapter checks the fit, not how much the handle will carry. That depends on the wood and the glue, and the test is a loaded lift a few inches over a soft surface. The glue-up and clamping are in Glue, finish and mending. When you may chop is settled by your lease or building rules and by your neighbors, not by this manual. For anything heavy or valuable, a furniture maker who can see the piece settles whether it will hold.

11. Knowledge check and scenario

Your ends are 3/4 in thick and your handle is 1 1/4 in high. What size is the tenon, and why?
1/4 in thick, one-third of the 3/4 in end, the traditional rule Popular Woodworking gives for hand-chopped mortises, and the width of a kit chisel. 5/8 in high, half the handle's height, leaving 5/16 in shoulders above and below. 3/4 in long, because a through tenon is as long as the end is thick.
Why chop a through mortise halfway from each face rather than straight through?
A chisel driven out of the far face bursts the fibers there, exactly where the joint shows. Chopping from both faces cuts each face's edges from the outside. It also halves the depth each pass has to reach, which keeps the walls straighter.
Why are the mortise's end walls chopped last?
The waste is levered out against the chisel, and the chisel bears on whatever is behind it. If the end walls are already at the line, the levering crushes them, and the crushed wall shows as a gap at the shoulder.
Why is the shoulder line on the handle taken from a side rather than measured?
The distance between the shoulders has to equal the tote's inside length. Laying the handle on a side and knifing at its rabbet shoulders (or its baselines) copies that length exactly, with no number to read or transfer.
(Go deeper) Your ends' grain runs across. Which way do the wedge kerfs run in the handle's tenon, and which walls of the mortise get the flare?
The kerfs run across the end's grain, so up and down the tenon, and the flare is pared on the mortise's long walls, which are its end-grain walls. The wedges then push against end grain, which bears the pressure, rather than long grain, which splits (Woodcraft, Burton; Popular Woodworking, Schwarz).
(Go deeper) Why does a drawbore pin need an offset, and how much does Andy Rawls use?
The hole in the tenon is bored a little nearer its shoulder than the hole in the mortise, so the pin, driven through both, pulls the shoulder tight against the mortised part. Rawls' rule is 1/16 in at most; more risks breaking the pin.
It is 9 p.m. You have laid out both mortises on the tote's ends and want to chop them tonight. Your neighbors below have not said anything about noise before. What do you do?
Heavy blows are louder and harder on a bevel-edge chisel, which Popular Woodworking says is not designed for heavy chopping; they also make a split more likely. And no one has told you mallet work after 9 p.m. is fine. Your lease or building rules set quiet hours, and asking the neighbor settles the rest.
The sawing and paring are quiet, so the evening is not lost. Chopping goes to the hours your building allows, and you can ask the neighbor in the meantime. The tenons fit against the mortises tomorrow, so leave them a little fat.
A solid block on the floor takes the blow better than a light table, and light blows are kinder to the chisel. But the floor is the neighbor's ceiling, and the sound still travels through it. It is a reasonable setup for daytime; it does not answer the question of the hour.

Checklist

Records your learning only; it is not a qualification.