The first tools: a small kit, new or used, and what can wait
What each tool in a small hand-tool kit is for, the one thing to check when buying it new or secondhand, and the tools that can wait.
Start here Essentials
At minimum this chapter asks you to compare the kit list with what you already own, and to get the four tools the bench hook needs. Everything else waits until the chapter that uses it. Everything marked Go deeper is optional on a first pass.
- Read the kit list for your project. Each tool is listed with its job in the tote and when you first need it (The kit for the tote).
- Check what you already have against it. Mark each tool in the tools and wood sheet, and check any used or inherited tool before trusting it (Buying or inheriting used tools).
- Buy or borrow the four tools the quick start needs. A saw, a square, a knife or sharp pencil, and two clamps (Buying new).
- Leave the rest until the chapter that uses it. Mark those tools "can wait" (What can wait).
Minimum time: about 30 minutes at home, plus one shopping trip. Done when: the kit sheet shows every tool as have, borrowed, to buy or can wait, with nothing bought that the tote does not use.
1. The kit for the tote Understand
A kit is sized to a job. The job here is the tote: a few short boards sawn to length and width, planed flat, marked out, and joined with a housing, a rabbet or a dovetail at the corners, and a tenon through each end for the handle. Every tool below does one of those jobs. A tool that does none of them is not in the list, however often it appears in other beginner lists.
The practitioners we read agree on the core and differ at the edges. The English Woodworker's beginner's kit and Paul Sellers' You don't need much both start with one bench plane, a few bevel-edge chisels, a square, a knife and a gauge. They differ on the saw and the plane, which Other kits, and Western saws sets side by side. The list below gives one default for each job.
| Tool | Its job in the tote | First needed in |
|---|---|---|
| Ryoba (a Japanese pull saw with rip teeth on one edge and crosscut teeth on the other) | Every cut: parts to length and width, tenon cheeks and shoulders, dovetails, housing walls | The quick start |
| Combination square or try square | Squaring lines across a board, checking a cut or a planed edge | The quick start |
| Marking knife (a pencil to start) | Cutting the lines the saw and chisel register in | The quick start |
| Two or more clamps | Holding work on the table, holding the planing board, the glue-up | The quick start |
| Marking gauge | Lines parallel to an edge or face: widths, thicknesses, joint depths | Marking out |
| Dividers | Stepping off equal spaces and proportions without numbers | Measuring without numbers |
| A 6 in or 12 in steel rule | Reading a size where a number is needed: buying boards, setting a gauge | Measuring without numbers |
| Three bevel-edge chisels, about 1/4, 1/2 and 3/4 in | Paring housings and rabbets, chopping the handle mortise, cleaning dovetails | Sharpening |
| Mallet | Driving a chisel for chopping | Housings and rabbets |
| No. 4 smoothing plane (or a No. 5 jack) | Flattening faces, straightening edges, bringing parts to width and thickness, the shooting board | Planing a board square |
| Double-sided diamond plate and a honing guide | Keeping the chisels and the plane blade sharp | Sharpening |
| Wood glue | The glue-up | Glue, finish and mending |
The first four are the quick-start kit. With them you can make the bench hook, which is the first thing this manual builds and the holding aid every other chapter uses. Nothing else in the table is needed until its chapter.
What each tool is, in a sentence or two
A ryoba cuts on the pull stroke, which lets the blade be thin; Woodcraft's guide to Japanese saws recommends it as the starter saw and notes that the thin blade leaves a thin kerf (the slot a saw cuts) and takes less effort. One edge has rip teeth, shaped like small chisels, for cutting along the grain; the other has crosscut teeth, shaped like small knives, for cutting across it. When the teeth dull, the blade is replaced rather than sharpened. We chose it as the default because one saw does both cuts, and because two of the practitioners' kits we read start with a Japanese saw. The same guide gives 210 mm (about 8 1/4 in) as a furniture size and 240 mm (about 9 1/2 in) for general work; either cuts tote parts.
A combination square has a steel blade that slides through a head and locks; the head registers against the board's edge and the blade gives a line at 90 degrees, and at 45 on the other side of the head. A try square is the fixed version, with no sliding blade. Either does the job if it is square, which is the one thing to check.
A marking knife cuts a fine line into the wood instead of drawing one on it. The saw and the chisel then have a groove to start in. A marking gauge is a beam with a sharp pin or wheel near one end and a sliding fence; set the fence, run it along the edge, and the pin scribes a line parallel to that edge. Dividers are two pointed legs on a hinge, set to a distance and walked along a board to step off equal spaces.
A bevel-edge chisel has its long edges beveled so it reaches into corners, such as between dovetails. Popular Woodworking's basic guide to chisels notes that it is not designed for heavy chopping, which is why the tote's handle mortise is small: it is cut in a few light blows at a time. Noor's (fictional) handle mortise is 1/4 in wide, so her 1/4 in chisel chops it to width in one pass.
A No. 4 smoothing plane is a short metal bench plane; the number is its size in the Stanley series, which Paul Sellers names alongside Record as the standard secondhand buy. Its sole is the flat bottom, its blade (also called the iron) is held at an angle by a casting called the frog, and a chipbreaker screwed to the blade curls the shaving. A No. 5 jack plane is the longer version, 12 to 15 in by The English Woodworker's figure.
A diamond plate is a flat steel plate coated with industrial diamond grit, coarse on one side and fine on the other. A honing guide is a small clamp on a roller that holds a blade at a set angle on the plate. The case for this pair over waterstones is in Sharpening.
2. Buying new: the one thing to check
For each tool, one feature decides whether it will do the job. Brand, finish and price mostly do not. This section names the feature and how to check it on the tool in your hand.
Square: the flip test
Robert W. Lang, in Measure, Mark and Lay Out, proves a square this way: hold its head against a straight edge, draw a line along the blade, flip the square over and draw again from the same point. If the two lines coincide or run parallel, the square is square. If they spread apart, it is not, and the gap between them is twice the actual error. Test it Popular Woodworking's All About Try Squares gives the same test step by step. You can do it in a store with a sheet of paper and the edge of a board or a straight shelf. Lang also advises checking your measuring tools against each other and setting aside any that disagree.
Saw: a straight blade and the teeth intact
Sight along a new ryoba's blade from the handle end. It should be straight. The crosscut teeth are fine and, Woodcraft notes, easily damaged; look along both edges for bent or missing teeth. A replacement blade fits the same handle, so check that the maker sells one.
Knife: which side is flat
A knife with a bevel on one side only cuts with its flat face against the square and its bevel toward the waste, as Yoav Liberman describes in An intro to marking knives. Single-bevel knives are therefore made for one hand or the other. Hold it as you would to mark, against a square, and check that the flat side faces the square. A knife beveled on both sides works in either hand. Test it
Gauge and dividers: points that hold
A gauge's fence should lock without slipping when you push on it. Dean Jansa, in Mystery of the Marking Gauge, describes the pin gauge in use: the pin barely engaged on the first pass, trailing rather than standing upright. A wheel gauge does the same job with a small sharpened disc. For dividers, George Walker's Essential Dividers says to check that the two points are the same length; the setting should also hold when you walk them along a board.
Chisels: a back that can be flattened
The back of a chisel, the flat face opposite the bevel, has to be flat near the edge, because it is one of the two faces that make the cutting edge. A new chisel's back is rarely flat out of the box; you flatten it once in Sharpening. What to check when buying is that the back is not visibly hollow or rounded at the edge, and that the handle is tight in the blade. Three sizes cover the tote: about 1/4, 1/2 and 3/4 in.
Plane: every part present
A new plane should arrive with its blade, chipbreaker, lever cap, frog and adjusters, and every adjuster should turn. Lie-Nielsen's bench plane instruction sheet is a useful map of the parts even if you buy another make: it shows the blade bedded at 45 degrees, bevel down, and the chipbreaker set about 1/16 in from the edge for general work. Product-specific Setting those parts is taught in Planing a board square.
Sharpening: dry or wet, and the grits
DMT's use and care instructions say its plates work dry or with water, start coarse for a neglected edge and finish fine, and should be washed and dried after use. Paul Sellers' sharpening notes name a double-sided plate as the cheaper of his two options. Check that the plate is wider than your widest plane blade, and that the honing guide holds both a chisel and a plane blade.
Clamps and glue
Clamps should open wider than your widest glue-up; for the tote that is the outside length plus the clamp's jaws. Glue has a working temperature on its label. Titebond's specifications for Titebond Original give 50 F as the lowest temperature for the glue, the air and the wood. Product-specific That matters in an unheated garage; Glue, finish and mending covers it.
This chapter does not say which brand to buy, and it does not say a cheap tool will or will not work. It says what to check on the tool in front of you. A tool that passes its check will do the tote's work; a tool that fails can sometimes be fixed and sometimes cannot, and the check tells you which question to ask next. Prices change and we give none from shops.
3. Buying or inheriting used tools
An old plane, saw or chisel from a parent's box or a flea market can be as good as a new one, and sometimes better. It can also be a part missing, a cracked casting or a kinked blade that no amount of work will put right. The checks below separate the two. None of them needs anything but your eyes and hands.
A plane
Paul Sellers' checklist for buying bench planes was written for online auctions, and it works just as well for a plane in your hand. In his words, a standard Stanley or Record No. 4 is the best example of a secondhand buy (You don't need much). Check:
- Original parts. Handles, knob, chipbreaker, lever cap and blade should all belong to the plane, not be retrofitted from another.
- No split knob or glued handle. Sellers says these rarely last. The rear handle (woodworkers call it the tote, not to be confused with the tote you are building) takes the push of every stroke.
- Enough blade. Look at how much of the blade stands above the rear handle when it is in place. A blade sharpened down to a stub has little life left.
- Rust. Surface rust is acceptable, Sellers says. Rust that has pitted the sole or the blade's back near the edge is more work.
- The sole. Sellers says its flatness is not something to judge from a photograph, and the eye tells you little more. Expect to work it. Sellers reports flattening a bad sole in about 15 minutes. Test it
- Cracks. Look closely at the cheeks either side of the mouth (the slot the shaving comes through) and around the frog. A crack in a casting is a reason to walk away; we found no source on repairing one.
A saw
Josh Clark, interviewed in Fine Woodworking's buyer's guide to antique handsaws, makes the blade (the plate) the first check. Sight down it from the handle. A slight bend can be worked out or may not matter; a sharp kink makes the saw bind in the cut, and he would not spend time on one. A chipped handle or a cut-down horn is acceptable if the saw feels right in the hand.
A used Western saw has another unknown: whether its teeth are sharp and evenly set. Set is the slight bend of alternate teeth outward, which makes the kerf wider than the plate so the saw does not bind. A dull or unevenly set saw cuts slowly and wanders. Sharpening saws is a skill that can wait (see What can wait), so a dull saw is a saw to send out or to set aside until then. The fair test is a cut: saw a scrap across on the bench hook and watch whether the saw tracks the line or steers off it. Test it
Chisels
A chipped edge looks bad and is the most fixable fault on a chisel. The chip is ground away in Sharpening; a deep one takes a while on a coarse plate, and a sharpening service is an option if it is too much to do by hand. Check instead what grinding cannot fix:
- The handle. OSHA's Hand and Power Tools booklet, written for employers, warns that loose or cracked handles let heads fly off and that mushroomed heads on struck tools can shatter. A cracked handle or one that turns in its socket is replaced before the chisel is struck with a mallet.
- The back. Pitting from rust right at the edge has to be ground or flattened past before the edge is whole. Pitting further back does not matter.
- The blade's length. A chisel sharpened down to a short stub still pares, but it is hard to sight square.
The same OSHA booklet also notes that a chisel used as a screwdriver can break, and that the greatest hand-tool hazards come from misuse and poor maintenance. Inherited chisels often show that history. It is also where OSHA says that dull tools can cause more hazards than sharp ones; that is workplace guidance, and a sharp chisel still cuts skin.
A mallet, a square and a gauge
A wooden mallet's head should be tight on its handle; a loose head can come off mid-blow. An old square gets the same flip test as a new one, and an old gauge the same check that its fence locks.
Write every check you make in the "checks done" column of the tools and wood sheet, so the next time you pick up the tool you know what you have already looked at.
4. What can wait
A tool that waits may still be useful one day. It is a tool the tote does not use, or a skill the first project does not need. Buying it now spends money and storage space before you know how you work.
- Other planes. A block plane, a jointer, a rabbet plane or a shoulder plane each do one job better than the No. 4. The tote's rabbets and housings are cut with a saw and chisel. The English Woodworker's list says planes of other sizes can wait. Paul Sellers' Knifewalls makes the case that a shoulder cut from a knife line comes off the saw square enough that a shoulder plane becomes a luxury.
- Saw sharpening. The English Woodworker puts it plainly: you do not need to know how to sharpen a saw to get into woodworking. A ryoba's blade is replaced; a Western saw can be sent out.
- A router plane and a plow plane. A router plane levels the floor of a housing to a set depth; a plow plane cuts grooves. Both are named in Housings and rabbets as options. The tote can be made without either.
- A workbench. A shop on a table holds the work without one.
- Mortise chisels and firmers. Heavier chisels for heavier chopping. The tote's mortise is small enough for a bevel-edge chisel struck lightly.
- A miter box. The tote has no miters; Learn Art Framing on frames covers mitered corners.
- Power tools. This manual is hand tools only.
Mark each of these "can wait" in the kit sheet if someone has offered you one, so the sheet shows the whole picture.
Go deeper 5. Other kits, and Western saws
Three practitioners' starting kits
The default kit above is ours, chosen for the tote and the table. Three practitioners publish their own, and where they differ is worth seeing.
| Item | The English Woodworker | Paul Sellers | The Hand Tool School |
|---|---|---|---|
| Plane | One No. 5 jack (12 to 15 in), with a couple of blades | A secondhand No. 4 as the best used buy; premium planes are preference, not necessity | A low-angle jack plane |
| First joinery saw | A Japanese back saw, rip cut | A 10 in, 17 teeth-per-inch gent's saw; nothing with 20 teeth per inch | One hardware-store handsaw |
| Chisels | Three bevel-edge: up to 1/4, 3/8 to 1/2, about 3/4 in | Four: 1/4, 1/2, 3/4 and 1 in | Three |
| Marking | Combination square, 6 in rule, knife, pencil, tape, marking gauge | Not listed in that post | Combination square, knife |
| Also | A cheap hardpoint panel saw, a mallet | A lifetime kit mixing new and secondhand for about GBP 600 (2023) | A brace and three bits (a cordless drill acceptable) |
| Source | Beginner's kit | You don't need much | Orientation |
The jack against the smoother is the clearest disagreement. A longer plane straightens an edge more easily; a shorter one is lighter on a table and leaves a finer surface. For short tote parts on a table we default to the No. 4, as Sellers does, and a reader who finds a No. 5 first loses nothing. The Hand Tool School's brace is for its workbench, which this manual does not build.
Western saws
A Western saw cuts on the push stroke, so its plate must be thicker to stay straight under compression Physical principle, and a backsaw carries a stiff spine along its top edge to keep the plate straight. Western saws are resharpened rather than thrown away, and a good one lasts a lifetime. Their teeth come in rip and crosscut patterns, usually on separate saws. Lee Valley's rip and crosscut tenon saws page gives one maker's figures: the rip at 9 teeth per inch, the crosscut at 12, with alternating bevels on the crosscut teeth that sever rather than tear the fibers. Product-specific
The case for a Western saw as the first saw is Sellers': a crosscut backsaw for joinery, with a rip saw for longer cuts, both resharpenable. The case for the ryoba, which this manual takes, is one saw for both cuts and a thin, low-effort pull stroke. Two practical differences show up on a table. A push stroke drives the work into the bench hook's fence, which is what the hook is built for. A pull stroke draws the work toward you, so the holding hand does more, as A shop on a table explains. If you already own a good backsaw, use it; the chapters work with either.
Chisel types
Popular Woodworking's guide to chisels separates three kinds. Bevel-edge chisels reach into corners and are not made for heavy chopping. Firmer chisels are thicker, for heavier work. Mortise chisels are thick enough to be driven hard with a mallet and to lever out waste. A beginner's set is bevel-edge because the tote's work is mostly paring.
Restoring a rusty plane
Taking an old plane back to bright metal, repainting it and replacing its handles is a hobby of its own. This manual stops at working condition: parts present, rust off the working faces, sole flat enough to plane, blade sharp. We do not teach restoration beyond that.
6. See it See it
Hal (fictional) sorts his father's tools. Hal is 71 and has an unheated attached garage. His father's box holds a Stanley No. 4 with surface rust and all its original parts, a 26 in handsaw with a slight bend near the toe, four chisels with chipped edges, and a wooden mallet. He goes through the checks. The plane's knob and handle are sound, the blade stands well above the rear handle, and the rust has not pitted the sole: it goes in the sheet as "have, used, needs sole checked." He sights down the handsaw and sees a gentle bend, not a kink. The chisels' handles are tight and none is mushroomed; the chips are the only fault. The mallet's head is tight. He builds his tote with through dovetails, so he still needs a joinery saw: he buys a ryoba and keeps the handsaw for long cuts if it passes its test.
Known: each tool's condition as described. Assumed: that the chips in the chisels are shallow enough to grind out by hand, which is Hal's guess from looking; it is settled at the plate in Sharpening, or by a sharpening service if the plate is too slow. Open: whether the bent plate cuts true, settled by a test cut on the bench hook; and whether the plane's sole is flat enough to work, which nobody can see from looking and which he checks when he sets the plane up in Planing a board square.
- Which hand tools do I need to get started?, The English Woodworker: a practitioner's beginner kit, tool by tool, with what can wait.
- Choosing and using Japanese saws, Woodcraft: the ryoba, its two edges and its sizes, with photographs of the teeth.
- All about try squares, Popular Woodworking: the flip test drawn out, and how to knife a line round a board.
7. Practice Practice
Minimum: every tool in the kit table entered in the kit sheet with a status, and the square checked by the flip test. Time: about 30 minutes, longer if you have a box of inherited tools. Materials: whatever tools you already have, a sheet of paper, a pencil, a board with one straight edge, and the tools and wood sheet.
- Lay out what you have. Every tool on the table, on the sacrificial board, edges away from you.
- Match it to the kit table. For each row, enter the tool in the kit sheet as have, borrowed, to buy or can wait.
- Flip-test the square. Draw, flip, draw again. Write the result in "checks done".
- Check each used tool. Plane, saw, chisels and mallet against the lists in Buying or inheriting used tools. Write what you checked and what you found.
- Write the shopping list. Only the rows marked "to buy" that the quick start or the chapter you are about to open needs. Everything else stays "can wait" for now.
- Test-cut a used saw (Go deeper; optional). One crosscut in scrap on the bench hook, watching whether it tracks the line.
8. Your setup Your setup
9. Check your work Check your work
Criteria
- Does every tool in the kit table have a status in your sheet?
- Has the square passed the flip test, or been set aside?
- Does each used tool have its checks written down?
- Is everything on the shopping list needed for the quick start or the chapter you are about to open?
- Is anything on the list there because a general beginner list included it, rather than because the tote uses it?
Worked example
Noor (fictional) owns no tools. Her sheet shows the ryoba, a combination square, a marking knife and two clamps as "to buy", for the bench hook. She marks the gauge, dividers, rule, three chisels, mallet, No. 4, diamond plate, honing guide and glue as "to buy, later": each goes on the list when she opens its chapter. Her tote has rabbeted corners, so she needs no dovetail tools beyond the ones already listed, and her 1/4 in chisel matches her 1/4 in handle mortise. A friend offers a block plane; she borrows it and marks it "borrowed", but it is not in her plan. At the store she does the flip test on two combination squares; one fails, with lines spreading at the far end, and she buys the other. Her sheet passes every criterion.
Common mistakes
- Buying a boxed set. Sets often hold sizes the tote does not use. Buy the three chisel sizes the tote needs.
- Trusting a square because it is new. The flip test takes a minute and catches a bad one.
- Discarding a chipped chisel. A chip grinds out. A cracked or loose handle is the fault to look for.
- Buying a used plane from a photo alone. Sole flatness and cracks do not show. Expect to work the sole, and ask about cracks.
- Buying everything before the first cut. Make the bench hook with four tools first; you will know more about what you want afterward.
What is still unresolved
- How sharp is sharp, and how to get the chisels and blade there: Sharpening.
- Whether your used plane's sole is flat enough, and how to set the plane: Planing a board square.
- Whether a bent saw cuts true: a test cut, explained in Sawing to a line.
- Where the tools live between sessions: A shop on a table.