Reference
Glossary
Plain definitions of the words woodworkers, lumber stores and tool makers use, from actual size to winding sticks.
Each term links the chapter that teaches it. Some words are store terms with a standard behind them (nominal size, S2S); some are shop terms that different writers use slightly differently (secondary bevel, microbevel). Where writers differ, the definition says so.
| Term | What it means | Where it is explained |
|---|---|---|
| Actual size | A board's real dry dimensions, as opposed to its nominal size. A 1x6 is 3/4 by 5 1/2 in actual size under the American Softwood Lumber Standard | At the store |
| Baseline | The gauge line round the end of a board that marks how deep dovetail tails and pins are cut: usually set from the thickness of the mating board | Dovetails |
| Bench hook | A flat board with a fence across each end, one on each face. The lower fence hooks over the table edge and the work is pushed against the upper one for sawing | A shop on a table, Make a bench hook this weekend |
| Bevel | The sloped face ground on a chisel or plane blade that meets the flat back to make the edge | Sharpening |
| Bevel-edge chisel | A chisel whose long edges are bevelled, so it reaches into tight corners such as between dovetails. Popular Woodworking says it is not designed for heavy chopping | The first tools |
| Board foot | A unit of lumber volume: 144 cubic inches, a board 1 in thick, 12 in wide and 12 in long. Softwood is counted from nominal sizes; hardwood yards usually tally at rough thickness, so ask | Choosing wood |
| Burr | A thin wire of metal that forms on the back of an edge when the bevel has been honed right to it. Feeling for it tells you the bevel reaches the edge; it is then removed on the back. Also called a wire edge | Sharpening |
| Cheek | One of the two broad faces of a tenon, which bear against the mortise walls | Mortise and tenon |
| Chipbreaker | The plate screwed to a bench plane's blade just behind the edge. It bends the shaving up and out, and set close to the edge it reduces tearout. Lie-Nielsen sets it about 1/16 in back for general work | Planing a board square |
| Crosscut | A cut across the grain, such as cutting a board to length. A crosscut saw's teeth sever the fibers rather than chisel along them | Sawing to a line |
| Cup | A curve across a board's width, so the face is hollow from edge to edge. Flatsawn boards are the most prone to it | At the store |
| Dado | The American name for a housing: a groove cut across the grain to hold a shelf or divider | Housings and rabbets |
| Dividers | A two-legged tool with sharp points that holds a distance and steps it off, so equal spaces and proportions can be laid out without numbers | Measuring without numbers |
| Dovetail | A corner joint of flared tails on one board fitting between pins on the other. It resists pulling apart in one direction by its shape alone | Dovetails |
| Drawbore | Pinning a mortise and tenon with the hole in the tenon slightly offset toward the shoulder, so driving the pin pulls the joint tight without clamps. One Popular Woodworking author keeps the offset to 1/16 in at most | Mortise and tenon |
| Dry fit | Assembling the parts without glue to check every joint, the clamps and the order of work before the glue goes on | Glue, finish and mending |
| Equilibrium moisture content | The moisture content wood settles at in air of a given temperature and humidity. At 70 F, 50 percent humidity gives about 9 percent, by the Wood Handbook's table | Choosing wood |
| Face edge | The edge planed straight and square to the face side and marked, from which widths and square lines are taken | Reference faces |
| Face side | The face planed flat first and marked, from which every gauge line and thickness on a part is taken. Also called the reference face | Reference faces |
| Fiber saturation point | The moisture content at which the cell walls are full of water and no free water is left in the cells, about 30 percent for most woods. Wood shrinks and swells only below it | Choosing wood |
| Flatsawn | Sawn so the growth rings run roughly along the board's wide face; the end grain shows arcs. Flatsawn boards change more across their width than quartersawn ones. Also called plainsawn | Grain |
| Frog | The casting inside a bench plane that the blade rests on. Moving it opens or closes the mouth in front of the blade | Planing a board square |
| Gauge line | A line scored by a marking gauge parallel to a face or edge, used for thicknesses, widths and joint depths | Marking out |
| Grain | The direction the wood's fibers run, usually along the board's length. Also used for the pattern the fibers and rings make on a face | Grain |
| Hide glue | Glue made from animal protein, used hot or as a liquid. Moisture and heat soften it, so a joint made with it can be taken apart and reglued, which is why furniture conservators favor it | Mending a loose joint |
| Honing guide | A clamp on a roller that holds a blade at a set angle while you hone it, so the bevel is the same every time | Sharpening |
| Housing | A groove cut across the grain of one part to hold the end of another, such as a shelf or divider. The British name for a dado | Housings and rabbets |
| Kerf | The slot a saw cuts, as wide as the teeth's set. It goes on the waste side of the line | Sawing to a line |
| Knife wall | A shallow V groove made by a knife line and a sloped cut on the waste side, so a saw or chisel has a wall to start against. Paul Sellers' term | Marking out |
| Lateral adjuster | The lever behind a bench plane's blade that tilts it side to side, so the cut is the same thickness across the mouth | Planing a board square |
| Marking gauge | A fence on a beam carrying a pin or wheel, set to a distance and run along a face or edge to score a parallel line | Marking out |
| Microbevel | A narrow secondary bevel at the very edge, honed at a slightly higher angle than the main bevel so only a little metal is honed each time. Makers differ on the angle: Lee Valley says 1 or 2 degrees above the main bevel, Lie-Nielsen calls its 10 degrees above a microbevel | Sharpening |
| Mortise | The hole or slot that receives a tenon. A through mortise goes all the way through the part | Mortise and tenon |
| Nominal size | The name a softwood board is sold by, such as 1x6, which is larger than its actual dry size. The standard sets which actual size each name means | At the store |
| Open time | How long glue can sit spread before the parts are put together and still bond. Titebond gives 4 to 6 minutes for Original at 70 F and 50 percent humidity | Glue, finish and mending |
| Paring | Taking thin slices with a chisel pushed by hand rather than struck, to trim a surface to a line | Housings and rabbets |
| Pin | In a dovetail, the part on the second board that fits between the tails. A half pin sits at each edge | Dovetails |
| PVA glue | Polyvinyl acetate glue, the white and yellow wood glues sold in squeeze bottles. Once cured it does not soften with water the way hide glue does | Glue, finish and mending |
| Quartersawn | Sawn so the growth rings meet the wide face at a steep angle; the end grain shows near-vertical lines. It changes less across its width, about half as much, and more in thickness. Publishers draw the angle limit differently | Grain |
| Rabbet | A step cut along the edge or end of a board, open on two faces, into which another part fits. Rebate in British usage | Housings and rabbets |
| Rip cut | A cut along the grain, such as cutting a board to width. A rip saw's teeth chisel along the fibers | Sawing to a line |
| Rough lumber | Boards as they come from the saw and kiln, not planed. Hardwood is sold rough by quarter-inch thickness: 4/4 is about 1 in thick rough | Choosing wood |
| S2S | Surfaced two sides: planed on both faces at the mill. A 4/4 hardwood board is 13/16 in thick S2S, by the Wood Handbook's table | Choosing wood |
| S4S | Surfaced four sides: planed on both faces and both edges, the way big-box boards are sold | Choosing wood |
| Secondary bevel | A second, slightly steeper bevel honed at the edge on top of the main (primary) bevel. A microbevel is a narrow one | Sharpening |
| Shooting board | A jig that holds work at 90 degrees to a track the plane runs on its side along, for trimming ends square in very fine amounts | Planing a board square |
| Shoulder | The cross-grain face where a tenon steps out to the full part. Tight shoulders hide the joint and resist racking | Mortise and tenon |
| Squeeze-out | Glue pressed out of a joint when it is clamped. Titebond says to wipe it with a damp cloth while wet, or scrape it once dry | Glue, finish and mending |
| Story stick | A strip of wood marked with every key size of a project, taken from the things themselves, used in place of a tape measure | Measuring without numbers |
| Tail | In a dovetail, the flared part on the first board, wider at its end, that fits between the pins | Dovetails |
| Tearout | Fibers torn below the surface by a plane or saw, leaving rough hollows, usually from cutting against the grain | Planing a board square |
| Tenon | The tongue on the end of a part that fits into a mortise | Mortise and tenon |
| Through tenon | A tenon that passes all the way through the other part and shows on its far face. It can be wedged or pinned | Mortise and tenon |
| Twist | A board whose face lies in two planes, so diagonally opposite corners are high and it rocks. Also called winding | Planing a board square |
| Winding sticks | A matched pair of straight, parallel sticks laid across each end of a board. Sighted from a few feet away, their top edges line up only when the face has no twist | Planing a board square |
Terms for joints and their proportions are compared in Which joint where, and terms for faults in When it goes wrong. The sources behind each definition are in the Resource library.